answersLogoWhite

0

Drill a hole and then insulate the hole with a rubber washer so the cable doesn't chafe on the jagged hole.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you run battery cables through he firewall of a 2002 impala?

You will need to drill a hole large enough for the cable being very careful not to damage anything on the other side of the firewall. You will need to purchase a rubber grommet to insert into the hole and then run the cable through to protect the cable. You only need to run one cable, as you can ground the negative cable near the battery. Why are you running a battery cable through the firewall in the first place?


How do you replace the Hood Cable in a 1998 Mercury Sable?

To replace the hood cable in a 1998 Mercury Sable, start by opening the hood and disconnecting the battery for safety. Remove the inner fender liner or any necessary panels to access the cable's routing. Detach the old cable from the latch mechanism and pull it out through the firewall. Install the new cable by threading it through the same path, securing it to the latch mechanism, and reassembling any panels or components you removed.


How do you change the battery cables in a Ford Mercury Mystique?

the whole cable or just the cable ends ??????????????


How do you relocate car battery in a 00 mercury cougar?

You'll need a battery box, RV supplies are readily available and some 4guage red cable - 10-12ft should do it. Look for ways to run the cable through the firewall down the edge under the carpet on the passenger side (original battery location correct?) Make sure that when you punch a hole in the firewall that nothing is in the way behind it! Where the wire will pass through the sheet metal insulate with a grommet to prevent shorting it out. Best to take out the backseat and go through that area into trunk. Its simple to run a new positive cable to the trunk area where your relocating it to. The negative can be bolted to the frame, choose a clean area and bolt it down real good.


Installation clutch cable 1990 Isuzu pickup?

To install a clutch cable on a 1990 Isuzu pickup, first, disconnect the negative battery cable for safety. Then, remove the old clutch cable by detaching it from the clutch pedal and the transmission. Install the new cable by threading it through the firewall and connecting it to the pedal and transmission, ensuring proper tension. Finally, adjust the cable if necessary and reconnect the battery.


How do you replace battery terminal on a 1999 Mercury Sable?

A battery terminal or a battery CABLE terminal. If the terminal is gone or destroyed on the battery, you need a new battery. If the cable terminal is terminal, you can buy an after market replacement or a complete new cable with terminal at most any auto parts store.


How do you Change battery for 2003 Mercury Mountaineer?

Disconnect the negative battery cable and then remove the positive cableRemove the battery heat shieldRemove the battery hold-down clamp boltLift out battery


Where is the starter relay on a 95 mercury mystique?

Follow the + battery cable should connect to relay


How to run power cable through firewall in my Monte Carlo?

looking under the firewall, follow the hoses and wires that go through the firewall. One will have enough room to squeeze the wires through. Make sure that you can reach the wires on the other side of the firewall as well.


Where is the speed sensor located on a 1994 Mercury Topaz 4 clynder?

I assume you have a cable speedometer. If so, just follow the cable on the firewall in the engine compartment to the transmission. When you take the cable out there is a small gear in there. That's it.


Is there a transmission sensor on 1992 Mercury Sable?

Yes, it's on the top of the transaxle casing midway between engine and firewall, on driver side. You will see the trans cable coming to join it from the firewall.


Where is the best place to go through the firewall to run a 12v wire from battery to an amp on a 1997 Chevrolet Tahoe?

By the brake pedal, since your connections to power will be right there, just follow the battery cable heading to the computer and you will see 2 terminals for 12v.