0
Why would the driver brake light go out on a 2002 Jeep Grand Cherokee when you hit the brakes?
Wiki User
∙ 14y ago
The light-bulb actually heats the base of the plastic lens assembly where the bulb plugs into. This allows the metal contacts for the bulb to sink into the plastic a little bit, causing the metal to loose contact with the bulb.
The simple fix is to pry the metal contacts up a little so they will make contact with the bulb again. It doesn't take much, so be careful.
Wiki User
∙ 14y ago
Wiki User
∙ 16y agoCheck under dash at your brake pedal for a plunger sensor, the brake pedal may not let it be releasing. Brake pedal arm pushes it in to activate the lights
Wiki User
∙ 15y agoEither the brake light switch is out of adjustment, or has gone bad.
Wiki User
∙ 14y agoThe circuit board/socket in the tail light has failed.
Wiki User
∙ 11y agoFailed circuit board on the back of the light.
Add your answer:
Earn +20 pts
You have 2004 Jeep Grand Cherokee Laredo brake and abs light is on how can you fix it?
How to change the brake switch on a 2004 Jeep grand Cherokee Laredo
What would cause the brake tail light fuse to blow each time you apply the brakes on a 1993 grand Cherokee jeep?
There is a dead short to ground in the circuit.
Why does your 2001 Jeep Grand Cherokee Laredo steering vibrate when you apply the brakes?
Warped brake rotors. This is a very common problem for the 1999-2004 Grand Cherokees. You will need to have your rotors replaced, or resurfaced. The best resurface method is with an on car brake lathe.
Why would only your third brake light work when brakes are applied in your 1996 jeep grand Cherokee?
your left and right bulbs are problay bad they are two filament bulbs the park filiments are good and the brake filament is bad
What type brake fluid does a 2005 Jeep Grand Cherokee 5.7 liter engine take?
A 2005 Jeep Grand Cherokee uses DOT 3 fluid.
You have 2004 Jeep Grand Cherokee Laredo brake and abs light is on how can you fix it?
How to change the brake switch on a 2004 Jeep grand Cherokee Laredo
What would be causing a scrubbing noise in rear brakes when you already replaced brake pads in a 96 grand jeep Cherokee Laredo?
The brake pads might not be adjusted properly. The brake pads can be too tight and have contact with the rotors.
What would cause the brake tail light fuse to blow each time you apply the brakes on a 1993 grand Cherokee jeep?
There is a dead short to ground in the circuit.
Why does your 2001 Jeep Grand Cherokee Laredo steering vibrate when you apply the brakes?
Warped brake rotors. This is a very common problem for the 1999-2004 Grand Cherokees. You will need to have your rotors replaced, or resurfaced. The best resurface method is with an on car brake lathe.
How does the emergency brake work on a 2003 Jeep Grand Cherokee?
The emergency or parking brake on 2003 Jeep Grand Cherokee operates a set of brake shoes inside a hub on the rear axles, this is incorporated into the disc brake setup.
Does a Jeep Grand Cherokee have a brake light switch?
Yes.
Why would only your third brake light work when brakes are applied in your 1996 jeep grand Cherokee?
your left and right bulbs are problay bad they are two filament bulbs the park filiments are good and the brake filament is bad
Brake repair on a 1996 grand Cherokee Laredo jeep?
Problem?
How do you change brake light switch on 93 Jeep Grand Cherokee?
The 1993 Jeep grand Cherokee brake light switch simply plugs in and out. The brake light switch is located beneath the dashboard on the drivers side of the engine compartment.
How to install brakes for a 2002 Pontiac Grand Prix?
Remove the tire and wheel from your 2002 Pontiac Grand Prix. Remove the spring from the brake shoe. Remove the brake shoes. Reverse the process to install the new brakes.
Where are the wheel bearings located on a 2004 jeep grand Cherokee?
In the brake rotors.
How do you find brake light fuse 2003 Jeep Grand Cherokee?
The brake light fuse on a 2003 Jeep Grand Cherokee can be found by looking at the cover to the main fuse box. It identifies each fuse and its location.
