answersLogoWhite

0

Yes and No. A 277 volt heater uses 1 "hot" wire and a neutral, And 240 volt uses TWO hots (120 volts each) and NO neutral unless it has a 120V blower unit just to get that out there. Theoretically you could use 240 volts. Because 240 volts is a Lower (and there are also heaters 120v Hot to Neutral btw) voltage you would Decrease the wattage output of the heater itself which would violate the UL rating of the heater. Here's the Math. Rated Voltage x Rated Amperes = Rated Wattage Output. So if you have a 1500W unit @ 277V it draws 5.41A. Now that you know that you take Ohms Law to find the total Resistance of the Unit which would be 277A / 5.41 = 51.1 Ohms/Resistance. If you take Ohms Law again but for Amperes and factor in 240V instead the math would be 240 / 51.1 Ohms =4.69A. Now take 240V x 4.69A = 1125Watts. You can see that the output is way lower then the maximum rating of the heater. This is for purely resistance heaters like baseboard and and Ceiling Tile heaters. None the less if you installed this on 240V and it is not UL or CE listed for it you violated the rating and the National Electric Code. If you want a better idea look at 240V heaters most are Dual rated for 240V and 208V and you will see the same difference in output wattage listed on the unit.

User Avatar

Wiki User

10y ago

What else can I help you with?

Continue Learning about Natural Sciences

How many amps does a 240 volt 1500 watt electric base board heater use?

To calculate the amperage for a 240-volt, 1500-watt electric baseboard heater, you can use the formula: Amps = Watts / Volts. For this heater, it would be 1500 watts / 240 volts, which equals 6.25 amps. Therefore, the heater uses approximately 6.25 amps.


Can a 277 unit heater be supplied with 240 volts?

No, a 277-volt heater cannot be safely operated with a 240-volt power supply. Matching the correct voltage is essential for the safe operation of electrical devices. Using a lower voltage than the device is rated for can lead to insufficient performance and potential damage.


How do you use 110 heater to 220 volts supply?

You don't. The heater will operate over its given specified wattage. A 120 volt heater run off of 240 volt will have an output increase. Ohms law stated that current is directly proportional to the applied voltage and inversely proportional to the resistance of the circuit. A 240 volt heater can be run off of 120 volts but the wattage will be reduced. For example if an ordinary 1000 watt baseboard heater's supply is 120 volts, the current of the heater will be, I = W/E 1000/120 = 8.3 amps. The resistance of the heater is R = W/I (squared) =1000/8.3 x 8.3 (69) = 14.5 ohms. Applying 240 volts on the same heater whose resistance is 14.5 ohms results in a new heater wattage rating. W = E (squared)/R = 240 x 240 (57600)/14.5 = 3972 watts. This is 2972 watts, almost 300%, higher than the manufacturer's designed safety rating. The amperage drawn by connecting a 120 volt, 1000 watt heater to a 240 volt source will be, I = W/E = 3972/120 = 33 amps. W = watts, I = amperage, R = resistance in ohms and E = voltage.


A 50 gallon electric water heater that uses 2 elements is normally what voltage?

A 50 gallon electric water heater with 2 elements is typically connected to a 240 volt power supply. Each element is designed to run on 240 volts to efficiently heat the water in the tank.


Can you use 240 volts with a 120 volt supply?

No, it is not possible to use 240 volts with a 120 volt supply directly. You would need a transformer to step up the voltage from 120 volts to 240 volts. Attempting to use 240 volts with a 120 volt supply without a transformer can damage equipment and pose a safety hazard.

Related Questions

Can i run a 240 volt water heater on 120 volt?

No. A water heater requires a 240 volt connection and cannot be re-wired to run on 120 volts. There isn't enough amperage in 120 volts to power the heating rods that are inside.


How many amps does a 240 volt 1500 watt electric base board heater use?

To calculate the amperage for a 240-volt, 1500-watt electric baseboard heater, you can use the formula: Amps = Watts / Volts. For this heater, it would be 1500 watts / 240 volts, which equals 6.25 amps. Therefore, the heater uses approximately 6.25 amps.


How many volts can b drawn off a 240 volt breaker?

240 volts maximum.


Can a 277 unit heater be supplied with 240 volts?

No, a 277-volt heater cannot be safely operated with a 240-volt power supply. Matching the correct voltage is essential for the safe operation of electrical devices. Using a lower voltage than the device is rated for can lead to insufficient performance and potential damage.


How do you use 110 heater to 220 volts supply?

You don't. The heater will operate over its given specified wattage. A 120 volt heater run off of 240 volt will have an output increase. Ohms law stated that current is directly proportional to the applied voltage and inversely proportional to the resistance of the circuit. A 240 volt heater can be run off of 120 volts but the wattage will be reduced. For example if an ordinary 1000 watt baseboard heater's supply is 120 volts, the current of the heater will be, I = W/E 1000/120 = 8.3 amps. The resistance of the heater is R = W/I (squared) =1000/8.3 x 8.3 (69) = 14.5 ohms. Applying 240 volts on the same heater whose resistance is 14.5 ohms results in a new heater wattage rating. W = E (squared)/R = 240 x 240 (57600)/14.5 = 3972 watts. This is 2972 watts, almost 300%, higher than the manufacturer's designed safety rating. The amperage drawn by connecting a 120 volt, 1000 watt heater to a 240 volt source will be, I = W/E = 3972/120 = 33 amps. W = watts, I = amperage, R = resistance in ohms and E = voltage.


A 50 gallon electric water heater that uses 2 elements is normally what voltage?

A 50 gallon electric water heater with 2 elements is typically connected to a 240 volt power supply. Each element is designed to run on 240 volts to efficiently heat the water in the tank.


What the difference between a 120 volt and a 240 volt waffle iron?

One has an element designed to work on 120 volts, the other has an element designed to work on 240 volts.


Can you use 240 volts with a 120 volt supply?

No, it is not possible to use 240 volts with a 120 volt supply directly. You would need a transformer to step up the voltage from 120 volts to 240 volts. Attempting to use 240 volts with a 120 volt supply without a transformer can damage equipment and pose a safety hazard.


What happens when 277 volt heater run on 240 volts?

When a 277 volt heater runs on 240 volts, it will not operate at its full capacity. This can lead to lower heat output and potentially damage the heater over time due to the difference in voltage. It is recommended to use the correct voltage to ensure safe and efficient operation of the heater.


Why do you only have 110 power to your electric water heater?

There are small water heaters that run on 110 volts. However if yours is a large 240 volt heater and you only have 110 volts going to it, then it is fused and one on the fuses has blown in the service panel.


What will happen if 120 volt appliance is plugged into 220 volt outlet explain with electrical equation?

If V is the rated voltage of the equipment, and Vs is voltage of the supply, we have this approximate equation: Vs = 2 V. That is enough to wreck the equipment and/or blow the fuse.120 volt appliance on 240 voltsThis senerio will use an electric baseboard heater but the results will be the same for any electrical appliance.The heater will operate over its given specified wattage. A 120 volt heater run off of 240 volt will have an output increase. Ohms law stated that current is directly proportional to the applied voltage and inversely proportional to the resistance of the circuit. A 240 volt heater can be run off of 120 volts but the wattage will be reduced.For example if an ordinary 1000 watt baseboard heater's supply is 120 volts, the current of the heater will be, I = W/E 1000/120 = 8.3 amps.The resistance of the heater is R = W/I (squared) =1000/8.3 x 8.3 (69) = 14.5 ohms.Applying 240 volts on the same heater whose resistance is 14.5 ohms results in a new heater wattage rating. W = E (squared)/R = 240 x 240 (57600)/14.5 = 3972 watts.This is 2972 watts, almost 300%, higher than the manufacturer's designed safety rating.The amperage drawn by connecting a 120 volt, 1000 watt heater to a 240 volt source will be, I = W/E = 3972/120 = 33 amps.W = watts, I = amperage, R = resistance in ohms and E = voltage.


How can I convert a 240 volt power source to a 120 volt power source using a 240 volt to 120 volt adapter?

To convert a 240 volt power source to a 120 volt power source using a 240 volt to 120 volt adapter, simply plug the adapter into the 240 volt outlet and then plug your 120 volt device into the adapter. The adapter will step down the voltage from 240 volts to 120 volts, allowing you to safely power your device. Make sure the adapter is rated for the appropriate wattage to avoid damaging your device.