0
You don't. The heater will operate over its given specified wattage. A 120 volt heater run off of 240 volt will have an output increase. Ohms law stated that current is directly proportional to the applied voltage and inversely proportional to the resistance of the circuit. A 240 volt heater can be run off of 120 volts but the wattage will be reduced.
For example if an ordinary 1000 watt baseboard heater's supply is 120 volts, the current of the heater will be, I = W/E 1000/120 = 8.3 amps.
The resistance of the heater is R = W/I (squared) =1000/8.3 x 8.3 (69) = 14.5 ohms.
Applying 240 volts on the same heater whose resistance is 14.5 ohms results in a new heater wattage rating. W = E (squared)/R = 240 x 240 (57600)/14.5 = 3972 watts.
This is 2972 watts, almost 300%, higher than the manufacturer's designed safety rating.
The amperage drawn by connecting a 120 volt, 1000 watt heater to a 240 volt source will be, I = W/E = 3972/120 = 33 amps.
W = watts, I = amperage, R = resistance in ohms and E = voltage.
What else can I help you with?
Does Korea use 110 or 220 electricity?
South Korea uses 220 volts electricity, whereas North Korea uses 110 volts.
How do you plug in a pot that is 220 to a 110?
Use a step-up transformer from 110 volts to 220 volts. Try getting one at Home Depot or SEARS.
How to configure 110 volts power supply to receive 220 volts?
A transformer is needed to convert 110 v to 220 v or vice versa. This type of transformer is commonly used in Europe for power tools in the building trade which run from a portable 110 v transformer with a centre-tapped earth for safety so that each side is only 55 v to earth. A 3 kVA transformer for this purpose costs about £80.
Will a 110 electric heater produce the same amount of heat as a 220 heater at 1000 watts?
No, a 1000-watt electric heater operating at 110V will produce the same amount of heat as a 1000-watt heater operating at 220V. The power output (in watts) determines the amount of heat produced, not the voltage.
How do you wire 220 volt from 2 110 volt lines. you have a concessions stand that is wired for 220 but everywhere you have been lately just keeps giving you 2 - 110 volt line?
To create a 220 volt connection using two 110 volt lines, you need to connect them in series. Ensure the two 110 volt lines are out of phase (provide opposite polarity) and then connect them together. This will result in a 220 volt supply for your concessions stand. It's important to consult a professional electrician to ensure proper wiring and safety.
You have a 94 caprice classic if you supposed to get 220 volts 2 your heater element and you just getting 110 volts so whats the problem?
WHAT????? I hope this is just a comment that you have a caprice and has nothing to do with either 110 or 220 volts Heater element implies either a furnace or a water heater. Where are you checking the voltage? If at the outlet and you only have voltage on one side of the plug it's most likely a fuse or breaker. If there is 220 at the outlet but element is not heating it is the element. Under no circumstance get 110 or 220 anywhere near a 94 Caprice classic
What is the current through the 150 ohm heater?
At 110 volts it is 0.8 amps. At 220 it is 0.4 amps. I=E/R. I=amps.E=volts R=resistance.
Can a 220 volt heating element operate on 110 volts?
220 heater on 110 voltsThe load is a resistive load and as such it is governed by Ohm's law. Current is directly proportional to the voltage and inversely proportional to the resistance. As the voltage goes down so does the current. For example take a 2200 watt heater at 220 volts = 10 amps. R = E/I = 220/10 = 22 ohms of resistance in the heater. Now take the 2200 watt heater and using the same formula and at 110 volts. I = E/R, Amps = Volts / Resistance. 110/22 = 5 amps. As you can see ohm's law holds true, the current is inversely proportional to the resistance and as the voltage goes down so does the current. To answer the question, yes a 220 volt heater will run on a 110 volt circuit but at 1/4 of the wattage that the heater is rated at. W = A x V = 5 x 110 = 550 watts. 500/2200 = .25 or 25%.
What voltage does and electric water heater use?
A standard domestic water heater in a house, apartment, etc will need 220 Volts AC. They have two heating elements upper and lower and each is 110 VAC hence the 220 Volt supply. Make sure it has a dedicated circuit and a disconnect on the wall above and beside water heater.
Does Korea use 110 or 220 electricity?
South Korea uses 220 volts electricity, whereas North Korea uses 110 volts.
Can you plug iPod Nano to a 220 volts to charge?
110 volts
How do you plug in a pot that is 220 to a 110?
Use a step-up transformer from 110 volts to 220 volts. Try getting one at Home Depot or SEARS.
How to configure 110 volts power supply to receive 220 volts?
A transformer is needed to convert 110 v to 220 v or vice versa. This type of transformer is commonly used in Europe for power tools in the building trade which run from a portable 110 v transformer with a centre-tapped earth for safety so that each side is only 55 v to earth. A 3 kVA transformer for this purpose costs about £80.
What will happen if an electric water heater which is designed for operation at 240 volts is connected to 120 volts?
240 heater on 120 volts The load is a resistive load and as such it is governed by Ohm's law. Current is directly proportional to the voltage and inversely proportional to the resistance. As the voltage goes down so does the current. For example take a 2200 watt heater at 220 volts = 10 amps. R = E/I = 220/10 = 22 ohms of resistance in the heater. Now take the 2200 watt heater and using the same formula and at 110 volts. I = E/R, Amps = Volts / Resistance. 110/22 = 5 amps. As you can see ohm's law holds true, the current is inversely proportional to the resistance and as the voltage goes down so does the current. To answer the question, yes a 220 volt heater will run on a 110 volt circuit but at 1/4 of the wattage that the heater is rated at. W = A x V = 5 x 110 = 550 watts.
Are dishwashers typically designed to operate on 110 or 220 volts?
Dishwashers are typically designed to operate on 110 volts.
How will a 3 phase panel give you 110 volts and 220 volts?
A three phase panel will not give you 110 and 220 volts. A three phase four wire panel will, but not at these voltages. The nearest voltages will be 120 and 208 volts. The 120 volt is the wye voltage of 208 volts. 208/1.73 = 120 volts. A single phase three wire panel will give you 110 and 220 volts.
Will a 110 electric heater produce the same amount of heat as a 220 heater at 1000 watts?
No, a 1000-watt electric heater operating at 110V will produce the same amount of heat as a 1000-watt heater operating at 220V. The power output (in watts) determines the amount of heat produced, not the voltage.
