answersLogoWhite

0

This is built into the logic of the on board chip. When you purchase a motion detector read the fine print to see what all of the functions are, as these fixtures can be used in many different applications. Some will stay on for 24 hours after a bump and then turn off automatically. Nice for the power company that turned it on in the first place. Some can over ride the automatic detection and can be used as a manual light switch. Best advice is to read the small print on the packaging.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Natural Sciences

Which land feature helps the most in filtering water to remove impurities?

Wetlands


What can happen if you remove energy from neon gas?

If you removed energy from neon gas, there would be a decrease in motion and more attraction between the particles.


Which feature was formed because more erosion took place than deposition?

A canyon or a valley may form when more erosion takes place than deposition. This can happen when the forces of erosion, such as water or ice, remove material faster than it can be replenished by deposition, resulting in a deep and steep-walled feature.


Why do nuclei that emit alpha particles such as americium-241 are safe to use in smoke defectors?

Actually, americium-241 is not safe. If you disassemble the smoke detector and remove the americium-241 pellet, and then ingest it, you are at risk of developing cancer, because an alpha emitter is dangerous when ingested. There are clear warnings on the smoke detector about this. The reason smoke detectors in general are safe is that the amount of americium-241 is very small, and it is very difficult to extract it from the smoke detector. Also, the alpha particles will not travel more than an inch or so in free air, and they will be stopped by the internal design anyway, so the alpha particle field inside the smoke detector is limited to the ion chamber, also inside the smoke detector.


How do you remove scratches from birthstone ring?

To remove scratches from a birthstone ring, you can use a jewelry polishing cloth designed for the specific metal of your ring. Gently rub the cloth over the scratches in a back-and-forth motion until they are less visible. If the scratches are deep, consider taking the ring to a professional jeweler for repair.

Related Questions

How do you unplug a smoke detector?

Remove the batteries from the back of the detector.


Do you have to remove earrings at the metal detector at airport?

No. The smallest item I have had to remove was my watch.


What are the steps involved in hardwired smoke detector installation?

Turn off power to the area where the smoke detector will be installed. Remove the old smoke detector, if applicable. Connect the new smoke detector to the existing wiring. Mount the smoke detector on the ceiling or wall using screws. Restore power and test the smoke detector to ensure it is functioning properly.


How can I replace a carbon monoxide detector?

To replace a carbon monoxide detector, first turn off the power to the detector. Remove the old detector from the wall or ceiling by following the manufacturer's instructions. Install the new detector in the same location, making sure it is securely mounted. Turn the power back on and test the new detector to ensure it is functioning properly.


How can I open a smoke detector to replace the batteries?

To open a smoke detector and replace the batteries, locate the battery compartment on the back or side of the detector. Use a screwdriver to remove any screws holding the compartment closed. Once the compartment is open, remove the old batteries and replace them with new ones, making sure to follow the correct polarity. Close the compartment and secure any screws back in place. Test the smoke detector to ensure it is working properly.


Do you have to remove your rings when you go through a metal detector?

Yes, or it will go off and they will make you remove them anyways, because most rings are made of metal.


What is keylogger detector software used for?

There are a variety of different keylogger detector softwares available. This software is used to encrypt files, detect and remove spyware and to protect one's computer from malicious activities.


How you get rid of a Trojan virus when your antivirus detector says it can?

Just click the link to buy the software and it will remove it. Or if you have the software click remove. Simples. *Meerkat Screech*


How can you cancel safesearch?

Remove it from your PC using the Add/Remove feature in the control panel.


How do you remove an executor of an estate in Michigan?

File a motion with the court. They will examine the motion and make a ruling.


Can your remove the motion blur in need for speed the run?

no


Am demodulator diode detector circuit?

demodulator circuit is a circuit which is used for remove all high frequency components from modulated signal.