answersLogoWhite

0

permanent attachment to an appliance

An appliance plug may have a differently shaped plug, in order to prevent it from being plugged into an ordinary electrical outlet (one with the wrong voltage or power rating).

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Natural Sciences

Can you change a dryer plug to fit a regular wall plug?

Different plugs are designed so that you can't plug an appliance into the wrong voltage. A dryer is usually 220-240 Volts and your standard outlet is 110-120 Volts. You can't do what you suggest.


How can you plug 2000 watts 240v into a 120v 20 amp breaker with out replacing your breaker and all the plugs on the line?

You cannot safely plug a 2000 watt 240v appliance into a 120v 20 amp breaker without risking damage or fire hazard. To use the appliance, consider installing a step-up transformer to convert the voltage from 120v to 240v before plugging it in. This will ensure the appliance operates correctly without overloading the circuit.


Why would you get a shock when unplugging an appliance that is turned off - I accidentally touched the metal prong on the plug as I was unplugging it - Was this why?

The switch to the appliance is down stream from where the power comes in from the plug. Even though the appliance is turned off at the switch the appliance has electricity up to the switch. As you stated there will be voltage potential right up until the pins of the appliance become disengaged from the receptacle If you have ever noticed a three blade plug, the ground pin is longer that the hot and neutral blades. What this accomplishes is that when plugging in a device the ground is made first and when un-plugging the ground is the last to be disconnected. By holding the appliance you were at the same ground potential as the appliance. By touching the "hot" side of the plug when pulling it out you became the return path for the electricity to flow. If you had touched the neutral side of the plug when pulling it out you would have felt nothing. Be careful when removing plugs from receptacles. Always pull on the plug body and never on the appliance's cord


How do you convert a hard wired appliance into a plug in type?

To convert a hardwired appliance into a plug-in type, you would need to install a plug onto the existing wires of the appliance. This involves cutting the wire, connecting it to the corresponding terminals on the plug, and securing the connection. It is important to follow electrical safety guidelines and, if you are unsure, consider consulting with a licensed electrician for assistance.


Why is there a fuse in a plug?

All UK-style 13-A plugs are fitted with a fuse for the purpose of overcurrent protection. The fuse rating must be appropriate for the load supplied by the plug, up to a maximum of 13 A.

Related Questions

How do you replace the plug on an appliance?

Plugs/cords can be purchased from appliance parts stores like www.appliancepartspros.com. Usually on the bag it will tell you how to replace. It is usually just a couple of screws.


How do you power a 1500 watt AC appliance in a car?

You can buy an "inverter." It plugs into the cigarette lighter or accessory plug or directly clips to the battery terminals and converts the 12 volt DC to AC. You can then plug your appliance into it. Be sure to get an inverter that is the right wattage capacity for your device.


How do i install neon rings on my subs i there is a lighter plug in with the on off switch and on the end is a plug were do i plug that plug into?

One end plugs into cig lighter the other end plugs into the neon light.


Are wall plugs parallel or series circuit?

They are parallel. Each plug is in parallel with the other plugs.


Why oven cable heats up?

If you are referring to the cable from oven to plug, this can be a sign of an electrical problem . Get an electrician or appliance tech to check it and the wall socket it plugs into.


How to change a plug on an electrical appliance?

To change a plug on an electrical appliance, first unplug the appliance and cut off the old plug. Strip the insulation from the wires, then attach them to the new plug following the manufacturer's instructions. Make sure the wires are securely connected and the plug is properly assembled before plugging in the appliance.


Can I use the mains plug on the back of my TV for anything?

Most UK 3 pin power plugs are fixed to the appliance cable at the factory. It is often possible to cut off the plug and adapt it to some other use, but it is better and safer to buy a new plug (which is fairly cheap) that is designed to be manually attached to a new cable.


How do you work Wii party power box?

It plugs into the back where one of the plug ins are and that plug goes into the the back of the other plug.


Can you plug in a 110v spa into a residential outlet?

If it's rated at 110 then you can safely plug it in to a residential outlet. But, because it is generating heat, it will be drawing substantial voltage so you should ensure that the appliance is on its own circuit; otherwise when someone else turns on a light, or plugs in another appliance, the circuit will overload and shut down.


What happens if you plug a 120V appliance into a 240V outlet?

You will burn up your appliance!!!!!


How do you replace the spark plugs on a Plymouth sundance?

you take out the old plugs remember where the 1st 2nd 3rd 4th plug wire goes put in your other plugs put the plug wires back on and there ya go


How do you get to the spark plugs to change them in a 1993 Ford Thunderbird?

removed plug wire, remove spark plug, gap new plug to spec. and reinstall. Repeat for every other cylinder. Would recommend replacing plug wires, cap and rotor when replacing spark plugs.