answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

How do you fix a slight leak going into the valve from the copper pipe you noticed when removing a radiator?

if it is a slow drip or sepage, it will make, @ particles in the water will fix it, if it is a steady drip then you will have to take it apart and wrap the pipe fitting with teflon tape, or use a pipe sealer on the threads,


How do you fix a leaking cold water pipe to the bathtub?

Well you will have to determine why it is leaking. It is just a loose fitting? try tightening it up with a wrench Is there a crack? Is the pipe white PVC (plastic) or copper or even gray metal? If it is any of these you will need to cut it out and replace that section. You might want to consider hiring a plumber.


WHY DO I HAVE to strike the pole -shake-then the light comes on?

it may be that there is a loose connection in the pole and or the light connectors(where you screw in the light) becomes a little rusted and when kick/shaken it loosens the rust and make connection. May be a loose connection, get it looked at by an expert, may be very dangerous!


What is the importance of pole sitao?

Pole sitao, a variety of winged bean, is important for its high nutritional content, including protein, vitamins, and minerals. It is also valued for its ability to fix nitrogen in the soil, improving soil fertility, and reducing the need for synthetic fertilizers. Additionally, pole sitao is a versatile crop that can be used in various culinary dishes, making it a valuable food source in many regions.


How do you repair water pipe vibration from all sinks?

This condition is caused by "water hammer". It's water pressure fluxuations caused by turning faucet on & off. To fix the problem, attach (solder?) a length of pipe, as long as possible, but 16-18 inches should suffice, with a cap on the end, installed vertically, with a tee joint, behind the faucet. Anywhere in the feed pipe near the faucet is OK, but the closer the better. When water is brought back up to poressure, a air shock absorber is created, and will solve your water hammer problem.

Related Questions

How can I fix a broken PVC pipe?

To fix a broken PVC pipe, you can cut out the damaged section using a hacksaw, clean the ends of the pipe, and then use PVC primer and cement to attach a new piece of PVC pipe or a coupling to the existing pipe. Make sure to follow the manufacturer's instructions for the primer and cement for a secure and leak-free repair.


How can I fix a leaking PVC pipe joint?

To fix a leaking PVC pipe joint, you can try tightening the joint with a wrench, applying PVC primer and cement to reseal the joint, or replacing the joint if it is damaged beyond repair.


Is there a way to fix a PVC pipe leaking in my home?

Yes, you can fix a leaking PVC pipe in your home by first identifying the source of the leak, then turning off the water supply, drying the area around the leak, and applying a PVC pipe repair kit or using PVC cement to seal the leak.


Explain how you can fix a leaky PVC water pipe?

Brake it down


How can I fix a broken PVC water pipe outside?

To fix a broken PVC water pipe outside, you can follow these steps: Turn off the water supply to the pipe. Cut out the damaged section of the pipe using a PVC pipe cutter. Clean and dry the ends of the remaining pipe. Apply PVC primer and cement to the ends of the pipe and the replacement section. Connect the replacement section to the existing pipe and hold in place for a few seconds. Allow the cement to dry completely before turning the water supply back on.


How can I fix a PVC pipe leak?

To fix a PVC pipe leak, you can use a PVC pipe repair kit or epoxy putty to seal the leak. First, turn off the water supply to the pipe. Clean and dry the area around the leak, then apply the repair material according to the kit's instructions. Allow it to dry completely before turning the water back on.


How can I fix a hole in a PVC pipe?

To fix a hole in a PVC pipe, you can use a PVC pipe repair kit or epoxy putty. First, clean and dry the area around the hole. Then, follow the instructions on the repair kit or epoxy putty packaging to apply the material over the hole. Allow it to dry and cure according to the instructions before using the pipe again.


How can I fix a PVC pipe leak efficiently and effectively?

To fix a PVC pipe leak efficiently and effectively, you can follow these steps: Turn off the water supply to the pipe. Clean the area around the leak with a rag and some sandpaper. Apply PVC primer and cement to the pipe and fitting. Quickly insert the fitting into the pipe and hold it in place for a few seconds. Allow the cement to dry for the recommended time before turning the water back on.


How can I fix a leaking PVC pipe in my plumbing system?

To fix a leaking PVC pipe in your plumbing system, you can follow these steps: Turn off the water supply to the affected area. Dry the area around the leak with a towel. Use a PVC pipe cutter to cut out the damaged section of the pipe. Clean the ends of the remaining pipe with sandpaper. Apply PVC primer to the ends of the pipe and the inside of a PVC coupling. Apply PVC cement to the primed areas and quickly connect the coupling to the pipe ends. Hold the connection in place for a few seconds to allow the cement to set. Turn the water supply back on and check for any leaks. If the leak persists, you may need to seek professional help.


How can I fix a PVC pipe?

To fix a PVC pipe, you can use PVC primer and cement to bond the broken pieces together. First, clean and dry the area around the break. Apply primer to both the pipe and fitting, then apply cement and quickly join the pieces together. Hold them in place for a few seconds to allow the bond to set. Allow the repair to dry completely before using the pipe again.


How do you remove a PVC flange glued to a PVC drain pipe?

pvc flange if glued properly can not be detached you just need to cut it and fix up a new one if the old flange is useless. www.pvcpipe.in


How can I fix a PVC pipe joint leak?

To fix a PVC pipe joint leak, you can start by turning off the water supply to the pipe. Then, clean the area around the leak and apply PVC primer and cement to the joint. Make sure to hold the joint together firmly for a few seconds to allow the adhesive to set. Finally, let the joint dry completely before turning the water supply back on.