0
What else can I help you with?
Would a 125 volt cord work with a 115 volt compressor?
Yes. The cord only transmits the power. Whatever that goes in is what comes out.
Is there a difference between a 9-volt 200mA power cord and a 9-volt 2 amp power cord?
Yes, there is a difference. The 9-volt 2 amp power cord can handle a higher current flow compared to the 9-volt 200mA power cord. This means it can power devices that require a higher current draw without being damaged.
Is sj cord rated for 300 volts to be used for 480 volt?
No, SJ cord is only rated for 300 volts and is not suitable for use with 480 volts. It is important to use the correct voltage rated cord for safety and to prevent damage to equipment. Look for cords that are specifically rated for 480 volts.
Can you replace a 10 amp 125 volt extension cord with a 10 amp 250 volt extension cord?
Yes the rated voltage is a maximum. A 250 v cord might be slightly thicker than one for 125 v. <<>> The voltage rating of an electrical extension cord is the insulation factor of the cord. These cords come in two insulation ratings, 300 volts and 600 volts. If the voltage rating is within the parameters of the cord maximums then it is safe to use it on that voltage. The amperage of the cord is based on the wire size of the cord's conductor. The rating of 10 amps will fall within the #14 cord size. Remember the longer the cord the larger the wire size should be to prevent voltage drop at the connected load end.
Can you use a 6 volt 2500mA power out put for a 6 volt 2000mA original power cord?
Yes, you can use a 6V 2500mA power output for a device that requires a 6V 2000mA power cord. The device will only draw the current it needs, so the higher amperage rating will not harm the device. It is important to match the voltage, but having a higher amperage rating is safe.
Can you replace a 7 amp 125 volt power cord with a 3 amp 125 volt power cord?
If the device you are powering requires 7 amps of power, then no. You will need to find a replacement cord with 7 amps. Check the power input requirements of the device to find out.
Can you use a 12 volt rated cord to power a 5 volt item?
no
If the power cord says 250 volts can you plug it in to a 100 to 240 ac adaptor input socket?
Yes, the 250 volt rating refers to the insulation rating factor of the cord and the maximum amount of voltage potential that the cord can safely handle.
Would a 125 volt cord work with a 115 volt compressor?
Yes. The cord only transmits the power. Whatever that goes in is what comes out.
Can a computer built in England on 240v work in a country that uses 110v?
Its all in the power supply. If there is a switch that lets you change the input voltage from 240 to 120 then you are fine. Most computers have this switch on the power supply, its located on the back of the computer up by the top. All you will have to do is change the plug on the cord to fit that country's 120 volt receptacle.
Is there a difference between a 9-volt 200mA power cord and a 9-volt 2 amp power cord?
Yes, there is a difference. The 9-volt 2 amp power cord can handle a higher current flow compared to the 9-volt 200mA power cord. This means it can power devices that require a higher current draw without being damaged.
Which is the positive terminal on a 3 prong 220 power cord?
A 220 volt power cord has 2 positive terminals. The will look the same. The one that is different will be the ground.
What type of cord is compatible with a Samsung dryer?
A Samsung dryer typically requires a 240-volt 4-prong power cord for compatibility.
What type of power cord should be used for an electric range?
An electric range should use a heavy-duty power cord that is rated for high voltage and amperage, typically a 4-prong cord with a 240-volt rating.
Can you use a 120 volt power bar with 240 volts power supply?
No, but check the specification on the power bar to see what its maximum voltage rating is. There will be a bit of cord end cutting to get the right configuration for 240 volt equipment.
What type of cord is required for a 3 prong oven?
A 3 prong oven requires a 240-volt electrical cord with three prongs to safely connect to the power supply.
Can I use a 12 volt DC 400 milliampere power cord on a device listed for 12 volt DC 100 milliampere?
Yes, of course! The information about milliamperes is just a limit the cord is able to lead. So 100 mA is less than 400.
