0
Some motors have a provision for connecting the individual windings in series or parallel to allow a choice of two different line voltages. Those motors have an externally accessible terminal board on them and their dual-voltage capability is usually indicated on the nameplate. Unfortunately, very few motors have this capability.
The only other way to run a 220 volt motor (actually it's 240 volts and 120 volts) from a 120 volt line is to use a 1:2 step up transformer. The transformer must be able to handle the current drawn by the motor; typically 3 to 5 amperes at 240 volts. Considering the cost of such a transformer, it's probably as cost effective to just replace the motor.
What else can I help you with?
What is the maximum volts that can be used on a 208 230 volt motor?
You should not go above 240 volts for that type of motor.
Can you rewire a mixer 120 volt motor to run a 220 volts?
It is not recommended to rewire a 120-volt motor to run on 220 volts, as it can damage the motor and pose a safety risk. It is best to purchase a motor designed to run on 220 volts to ensure proper functioning and safety.
Can a 220 volt lamp be converted to 110 volts without replacing the wiring?
Yes, lamp cord is rated in the 300 volt wire classification. This means that the cord is approved for use up to a maximum of 300 volts.
Can a ge 36volt motor be run on 48 volts?
The 36 volt motor will over heat (depending on the load of the motor)on 48 volts and melt the copper inside the motor you can rewind the copper inside to cope with the extra 12 volts.My answer would be not to try it as i have and it totaly melted the copper inside.
Can a 240 volt sub panel run 115 volt motor?
In Europe 240 volts is standard, so no a 115 volt motor will not work. In USA 120 volts is standard, so if your sub-panel has 120 volts, (check with voltage meter) then yes. Read carefully, To get 240 volts in a sub-panel in USA the electric company brings two (2) wires, each wire has 120 volts, 120 + 120 = 240. One of those 120 volts will run your motor. Look for the wires from the electric company and check them with your voltage meter. If this is a commercial application you will need to call an electrical contractor, power companies for commercial applications do not follow the above.
What type of motor is the inducer motor and a furnaces?
A 120 volt motor is the inducer motor. It works the furnace.
Why not put a 12 volt motor to replace the 120 volt motor in your freezer Will this work?
The voltage of 120 volts is more common that the lower voltage of 12 volts.
Can a 110 volt motor run on 240 volts without damage?
No, unless the motor was wound for dual voltage operation, which it will state on the motor nameplate, a 110 volt motor run on 240 volts will be damaged.
What is the maximum volts that can be used on a 208 230 volt motor?
You should not go above 240 volts for that type of motor.
Can you run a 480 volt machine with 600 volt incoming voltage?
Yes, but the 600 volts would have to be transformed down to 480 volts. Direct connection to the motor with 600 volts would overheat the motor to destruction.
Will a 500volt 50hz squirrel cage motor run on 380volts 50hz?
No, the voltage of 500 volts is too high to operate a 380 volt motor.
Can a 220 volt motor run on 440 volts?
No it will fry the motor use a voltege reducer
Can you rewire a mixer 120 volt motor to run a 220 volts?
It is not recommended to rewire a 120-volt motor to run on 220 volts, as it can damage the motor and pose a safety risk. It is best to purchase a motor designed to run on 220 volts to ensure proper functioning and safety.
Can you run 220 volt motor compressor a 380 volt supply using power inverter?
No 380 volts is too wide a spread to use a 220 volt motor on.
Will 220 volt work in a high volt 3 phase motor?
Yes a 208 voltage motor will operate on 220 volts. You have to increase the motor overload protection by 10% of the motor's full load amperage to protect the motor.
How many volts to run a 48 Volt club car electric motor?
If a 48 Volt club car electric motor requires 48 volts, then it should be given a 48 volt power source, or something close to it. Too many more volts and it may burn out; not enough volts and it may not run or it will try to draw too much power and burn out the power supply.
How can you tell if a motor is a 6 volt or a 12 volt?
Look on the motor case and the correct voltage should be printed there. Otherwise, see if it runs at the right speed on 6 volts.
