0
What else can I help you with?
How many T8 fixtures can go on one 20 amp circuit?
Divide 20A by the Amps listed on the label of each fixture ballast. A T8 bulb will use an electronic ballast. They generally run 1A for four 4 foot bulbs. Try 15 four bulb fixtures per circuit and use a 20A rated switch.
Can an overhead 400W light with built in ballast that is currently wired to use 480V be rewired to use 120V?
Only if the ballast is a multi tap ballast.:Even if you could install a 120V ballast, or tap it to 120V with the existing one, Current may become an issue. To run the 400W light (sodium?) Now instead of the .833 amp range it's more like 3.33 amps. Supply wiring would have to be able to handle that. Those types of lights are often on long runs to building and grounds lights, parking lots, etc. Using 480 saves a lot on wiring costs.
Can 6 unit of 6 volt bulb fit a 13 amp plug?
No, a 13 amp plug is designed for higher power devices like appliances and electronics. A 6 unit of 6 volt bulb typically requires much less power and would be better suited for a lower amp plug or a transformer.
When was The AMP created?
The AMP was created in 2003.
How would the circuits work in the Lightning Reaction Electric Shock Game if you don't know google it also how many amps and watts is safe in the machine?
There are 2 sides to each controller, one is the positive side and the other is the negative side. A current is sent through that to produce the shock. I think there is proberbly a transformer in there which steps up the voltage from the small one that the batteries produce to a higher voltage which is the shock. However I think the transformer would step down the amps so that it is a safe shock.
How does a shock pen amp work?
A shock pen contains a voltage transformer that activates when the pen is clicked, emitting a jolt of energy sometimes up to 756 volts. These are not intended for children or people with electronic devices in their body, with heart problems or epilepsy.
Can you run 1000 watt light and ballast with an overhead 60 watt light and a floor fan on a 15 amp breaker?
Yes, if that is all that is on the circuit.
Can amp kill children?
if enough is passed through the body amps can kill anyone
Will 106 volts kill a small dog?
maybe depending on the amp's because amp's is how powerful the current is.
Why will an electric guitar amp randomly shut off with the amp still on?
I have the same problem with my amp. When the amp gets warn out it overheats quicker than when it was new, so there is a safety built into the amp that will kill the speakers so you don't damage them. At this point you should have some repair on your amp, or buy a new one.
What does 4007 represents in 1n4007 transistor?
A 1n4007 is a diode and not a transistor, the 4007 don't really represent anything, the 1n4007 is a axial lead standard recovery rectifier, working peak reverse voltage = 1000V, the forward current for this device = 1 Amp. More data about it can be find in the data sheet.
How many floresent lights can go on one 15amp circuit?
The way you calculate this is by looking at the amperage marked on the ballast of the fixture. Different size fixtures have different size ballasts. A 15 amp circuit is allowed to be loaded to 80%. 80% of 15 is 12amps. Now all you have to do is divide the ballast current into 12 amps and you have the total number of fixtures that you can added to the circuit.
What will happen if you hook up a system and the amp rms is lower than the sub rms?
you could possibly kill your amp. because the subs are asking for a certain amount of power and your amp cant give the power. but typically the amp will push all its power avalible to the sub and you should be fine. but for the optimum sound system the amp rms should be the same or close to the sub rms.
How many T8 fixtures can go on one 20 amp circuit?
Divide 20A by the Amps listed on the label of each fixture ballast. A T8 bulb will use an electronic ballast. They generally run 1A for four 4 foot bulbs. Try 15 four bulb fixtures per circuit and use a 20A rated switch.
Can an overhead 400W light with built in ballast that is currently wired to use 480V be rewired to use 120V?
Only if the ballast is a multi tap ballast.:Even if you could install a 120V ballast, or tap it to 120V with the existing one, Current may become an issue. To run the 400W light (sodium?) Now instead of the .833 amp range it's more like 3.33 amps. Supply wiring would have to be able to handle that. Those types of lights are often on long runs to building and grounds lights, parking lots, etc. Using 480 saves a lot on wiring costs.
How do you by pass the amp so you can use your new sterio?
you take the tip of the chord and chew it till you get shocked, then you put it on your sister and kill her
Where is the number 32 fuse 50 amp on a 91 Honda civic dx?
It is in the Main Fuse box. That's the one behind the battery (but not the one on the battery) on the right side of the car on top of the shock tower. There are two 50-Amp fuses in it. It is the one at the bottom of the U-shaped box.
