If you have 12/2 wiring in this circuit and a 20-amp breaker controlling it, you can THEORETICALLY do it, but you've got another problem: according to code, if you've got a 20-amp breaker and a 20-amp outlet, you're only allowed to have one outlet in the circuit on the theory that a 20-amp outlet is going to have a 20-amp appliance plugged into it. If you want more than one outlet, you'll need to use 10/2 wire and a 30-amp breaker.
If you are asking this question, it implies you are not qualified to do the work. Hire a licensed electrician!
If the breaker is not already 20A, then absolutely not! An existing 15A breaker will have #14AWG wire to the outlet(s). For a 20A circuit, you must have a MINIMUM of #12AWG. If you try to push 20A through #14 wire, you could start a fire, not to mention it is illegal.
15A and 20A outlets are wired exactly the same, one just has a higher rating than the other.
A regular 120V outlet is already single-phase.
So, your question really is: Can an existing 15A, 120V circuit be converted to a 20A circuit by simply changing the breaker and receptacle to 20A? : No, the breaker, wiring, and receptacle(s) must ALL be changed to be safe and legal.
If the breaker is already 20A, and the wiring is already #12, then no modification is necessary. You are good to go as-is.
Tip: If your house has an outlet for a washing machine, check the breaker for it. Washing machines are supposed to have their own dedicated circuit, and that circuit is required to be 20A according to NEC article 210-11. You could use that outlet temporarily to do your welding.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicator
to insure the circuit is, in fact, de-energized.
if the wire is #12 or higher, then yes you can swap the breaker and receptacle. however, without ripping your drywall apart there is no guarantee that is #12 the entire run. back to your panel. if ihe wiring is open and you can verify its indeed 12 gauge....go for it.
It depends on the amount of current (Amps) your breaker is rated for. If you boost your voltage the current will go down proportionally. 10 guage wire has an allowable ampacity of 30A. so if you are not drawing more than 27A you should be ok.
No, you cannot simply cap one leg of a 240-volt circuit and change the breaker to convert it into a 120-volt outlet. This requires rewiring the circuit to provide 120 volts, including changing the outlet and possibly other components to be compatible with the lower voltage. It's recommended to consult with a licensed electrician to properly convert the outlet.
Yes, you can change an old circuit breaker box without rewiring the entire house, as long as the existing wiring is in good condition and meets current electrical codes. The process typically involves disconnecting the old panel, replacing it with a new one, and reconnecting the existing circuits. However, it's essential to hire a licensed electrician to ensure the work is done safely and up to code, especially if the new panel has different requirements. Always check local regulations and permits before proceeding.
Yes, it is possible to convert a dryer outlet into two separate circuits by rewiring and adding a new breaker for the second circuit. However, it's important to ensure that the electrical load and wiring capacity can accommodate the additional circuit to prevent overloading the system and ensuring safety. Consulting with a qualified electrician is recommended for this type of project.
Operating a breaker on a continuous current, close to the breaker's tripping point can cause this condition. Because the breaker is a thermal device the heat builds up over a time period. Check the breakers on either side of the faulting breaker. If these breakers are also warm from use they take away the heat sink effect and do not let the faulting breaker cool down. Check the current of the load to see how close you are operating to the breakers trip point. Over time the trip setting of the breaker can become lower to a point where it will not reset. Changing the breaker out should rectify this non resetting condition.
It depends on the amount of current (Amps) your breaker is rated for. If you boost your voltage the current will go down proportionally. 10 guage wire has an allowable ampacity of 30A. so if you are not drawing more than 27A you should be ok.
You can reduce the breaker size because that limits the current that can reach the main panel. There is no safety issue other than the significant danger in an unskilled person changing out a main breaker.
No, you cannot simply cap one leg of a 240-volt circuit and change the breaker to convert it into a 120-volt outlet. This requires rewiring the circuit to provide 120 volts, including changing the outlet and possibly other components to be compatible with the lower voltage. It's recommended to consult with a licensed electrician to properly convert the outlet.
Yes, you can change an old circuit breaker box without rewiring the entire house, as long as the existing wiring is in good condition and meets current electrical codes. The process typically involves disconnecting the old panel, replacing it with a new one, and reconnecting the existing circuits. However, it's essential to hire a licensed electrician to ensure the work is done safely and up to code, especially if the new panel has different requirements. Always check local regulations and permits before proceeding.
A 4500 watt element can work on a 20 amp breaker, but it may occasionally trip if the total load on the circuit exceeds 20 amps. It is recommended to use a 4500 watt element with a 25 amp breaker to ensure consistent performance.
Yes, it is possible to convert a dryer outlet into two separate circuits by rewiring and adding a new breaker for the second circuit. However, it's important to ensure that the electrical load and wiring capacity can accommodate the additional circuit to prevent overloading the system and ensuring safety. Consulting with a qualified electrician is recommended for this type of project.
Operating a breaker on a continuous current, close to the breaker's tripping point can cause this condition. Because the breaker is a thermal device the heat builds up over a time period. Check the breakers on either side of the faulting breaker. If these breakers are also warm from use they take away the heat sink effect and do not let the faulting breaker cool down. Check the current of the load to see how close you are operating to the breakers trip point. Over time the trip setting of the breaker can become lower to a point where it will not reset. Changing the breaker out should rectify this non resetting condition.
Definetely, in 23 yrs I have never had a case that would allow the wire/breaker to remain.
Either your breaker switch needs to be changed for a heavier one, the pool equipment needs to be put on an other circuit or better still one of its own.It is best to talk to an ellectrician about the delails involved.
If the circuit has not damaged the bus bars in the distribution panel just change the breaker out for a new one. If the wire insulation has burned you might want to think about changing the wire for a new one. Wire burn back is caused by loose terminal connections at the breaker. As a general maintenance procedure shut off the main breaker and go over all of the breaker terminal connections to make sure that they are tight.
You cant there are no cheatsAnswer:The only "cheat" would be changing the paddle speed which can be found in the options menu.
the stone breaker