Yes, but you will need to ensure that a 5-A fuse is fitted inside the plug. '13-A' is its nominal rated current; the actual current is determined by the load which, in your question is 5 A. So a 5-A device is perfectly safe to use with a 13-A plug.
The standard color coding for fuses in American wire is as follows: 15-amp fuse: blue 20-amp fuse: yellow 30-amp fuse: green
It is NEVER a good idea to use a higher value fuse. The reason for the 10 Amp fuse is that it blows at 10 amps which the wire and device being protected is designed to handle. If you substitute 15 amps and that amount of current flows in your device, it may destroy the device and other things in the path of the current.
The only way you can change a 15 amp to a 20 is you have to replace the 14 gauge wire going to it with a 12 gauge wire, then replace the 15 amp breaker with a 20 amp breaker. You can put a 15 amp outlet on a 20 amp circuit as long as there is more then one receptacle. A double receptacle counts as two receptacles. Steve Green Coeur d'Alene, Idaho
You can use the wire rated for 20 amps on a 15 amp receptacle but you can not use a 20 amp fuse on any device rated at 15 amps. This is a tricky part of the code about receptacle outlets, You can use a 15 amp duplex outlet on a 20 amp circuit. (duplex outlet two devices can plug in) If it is a single outlet then the outlet must be rated 20 amp. NEC table210.21(B)(3). ============ A 15 amp duplex receptacle can be wired to a 20 amp rated circuit. This means the breaker OR fuse protecting the circuit can be rated 20 amps if the wire is also rated at 20 amps (12 AWG). --Sparkfighter
No, it is not safe to use a 250V 15A fuse in a 125V circuit. The voltage rating of the fuse should match or exceed the circuit voltage to ensure safety. Using a lower voltage rated fuse can lead to overheating and potentially create a fire hazard. Always use the correct fuse rating for your circuit.
The 13 amp fuse with blow at the lower rate to the 15 amp fuse. And At 15 amp the motor is normally more powerful - check the wattage used in both
fuse number 1 is 10 amp fuse 2 is 25 amp fuse 3is 25 amp fuse 4 is a spare fuse 5 is 10 amp fuse 6 is a spare fuse 7 is 20 amp fuse 8 is 25 amp fuse 9 is 20 amp fuse 10 is 5 amp fuse 11 is 5 amp fuse 12 is a spare fuse 13 is 5 amp fuse 14 is 15 amp
The 1998 Ford Mustang owners manual shows : fuse # 13 - 15 amp - electronic flasher fuse # 18 - 15 amp - electronic flasher which fuse is for the turn signal flasher and which fuse is for the hazard flasher it does not specify
15 is the amp pf the cigarette lighter fuse in Astra envoy.
According to my Chilton repair manual: Fuse # 1 - 15 amp - for stop lamps/four-way flash/speed control inhibit Fuse # 11 - 15 amp - for park lamps / license lamps Fuse # 13 - 15 amp - for turn lamps/ back up lamps
15 amp fuse marked courtsy 15 amp fuse marked courtsy
15 amp fuse under hood, labeled in diagram as "CIGAR"
Under the hood driver side fuse box labeled Mil 15 amp fuse, just change it
No, you could overload the wiring and start a fire.
Under the hood back side #46 a 15 amp fuse
20 amp body fuse 20 amp body fuse #15 on the fuse block 25 amp body feed fuse
The purpose of a fuse it to protect the wire that goes to the load. A 15 amp fuse protects a #14 gauge wire. A 20 amp fuse protects a #12 gauge wire. To answer your question if the wire size is #12 coming from the 15 amp fuse now then it can be upped to 20 amp fuse. If it isn't then you are taking the risk of overloading the #14 wire with a 20 amp fuse. This can lead to insulation failure of the #14 wire, overheating with the possible outcome of a fire breaking out somewhere in the circuit.