0
yes, you would have to replace the single poll breaker with a 2 poll of the same trip rating. I use the word carefully often as a reminder, the circuit breaker panel is hot. If you have the luxury of turning off the main breaker, do so. It also assumed you have room for a 2 pole breaker.
Tools you will need; Flat head and/or Philips screwdriver, test light or meter, red electrical tape and wire cutters/strippers.
# With the cover carefully removed, locate the existing single poll circuit in your panel. # shut breaker off, verify with test light or meter. # Remove black wire from breaker and carefully trace back to where the wire comes into the panel. This will help you locate the paired white wire .
# Carefully remove the white wire from the neutral buss. Note: Leave the green ground wire where it is. All circuits must be grounded regardless of voltage!
# Using the red electrical (trace) tape, run a few turns of tape over the white insulation jacket to signify line 2 or another hot wire. White always represent neutral, red represents hot as does black. Note: You should repeat the trace tape step at the other end of this wire for safety.
# Neatly and carefully move new red trace wire to breaker location and pair with black. # Carefully remove existing breaker by prying the breaker up from opposite side of the screws, towards the direction of the screws.
# Carefully stab down new 2 pole breaker by first installing the foot (below the screws) of the breaker in the shoe or tab. Then carefully push the other end down over the buss bars. Note: the breaker must be in the off position. you'll get zapped other wise.
# install black wire in top screw and red trace wire in bottom screw, or match any existing 2 pole breakers in your panel. Tighten, but do not over tighten screws.
# Close up the panel flip the breaker as long as the other side is buttoned up and good luck.
What else can I help you with?
Can you use the 220v 50hz appliances in 110v 60hz?
Depends. Some smaller stuff can usually run on both, in which case it will be printed on them. If it isn't, you can't run a 220v item on 110v.
Can you run a 110v 20a circuit off one leg of a ge thqp 220v 20a breaker?
No, you cannot run a 110V 20A circuit off one leg of a GE THQP 220V 20A breaker. A 220V breaker is designed to provide two hot legs, each supplying 110V, but when using only one leg, it does not provide the proper grounding or neutral configuration needed for a standard 110V circuit. Additionally, this could lead to potential safety hazards and code violations. Always consult a qualified electrician for proper circuit configurations.
Why can't i connect a 220v appliance directly to a 110v power source?
Connecting a 220V appliance to a 110V power source can damage the appliance and potentially cause a fire. The appliance is designed to run on 220V input, so using a lower voltage can overload its components. It's important to use the correct voltage to ensure safe and proper operation.
If you plug a 1000 w portable heater into a 220v outlet will it burn out?
you must check the voltage and current rating for the heater, the power itself doesnt matter Concur - Some heaters may be rated for the higher voltage which requires less current to run. Watts = Current * Voltage. You risk a fire if you try to run heater above its rated values which should be on a plate on the appliance.
Is there anyway to get 220V 60hz from a 110V 50hz power supply?
It would involve some electronics work but it could be done. Might add that it could be more expensive than just buying the proper power supply. Use Use 220V 60hz motor to run 110V 50hz Generator.
Can you plug a 220v deep fryer into a 110v outlet?
No. Attempting to run an appliance on insufficient voltage can cause damage to the appliance and can be dangerous. Call an electrician and get him to install a 220v plug
Can you use the 220v 50hz appliances in 110v 60hz?
Depends. Some smaller stuff can usually run on both, in which case it will be printed on them. If it isn't, you can't run a 220v item on 110v.
Can you run a 110v 20a circuit off one leg of a ge thqp 220v 20a breaker?
No, you cannot run a 110V 20A circuit off one leg of a GE THQP 220V 20A breaker. A 220V breaker is designed to provide two hot legs, each supplying 110V, but when using only one leg, it does not provide the proper grounding or neutral configuration needed for a standard 110V circuit. Additionally, this could lead to potential safety hazards and code violations. Always consult a qualified electrician for proper circuit configurations.
How can you supply 220v machine to 208v supply?
Most 220 volt equipment will work on 208 volt supply. If the machine has a resistive load then the watts output will be lower than if supplied from a 220 volt source. If it is a motor load you will find that the equipment may run a bit slower but most motors will take the lower voltage. If the machine is a plug in device, install the appropriate receptacle to match the pin configuration and plug it in. If it is a hard wire installation this should be done by a qualified person.
Why can't i connect a 220v appliance directly to a 110v power source?
Connecting a 220V appliance to a 110V power source can damage the appliance and potentially cause a fire. The appliance is designed to run on 220V input, so using a lower voltage can overload its components. It's important to use the correct voltage to ensure safe and proper operation.
Can you replace the 240v plug on my 240v mitre saw with a 110v plug and run it off a 110v transformer?
Changing the plug will not change the power needed to run the saw. If the saw has a dual voltage motor then a wiring change can be done to switch the saw from 240 to 110 volts. If it is not a dual voltage system then the saw must be fed with 220 volts.
Can 110V appliances be used in 220V countries I have lighting and heating appliances which i bought while i was in the US. Now moved to India. Can i use these appliances directly with a 220V source.?
No, they will burn out. the wiring, motors and modules are built to run on and withstand 110v. There are rectifiers that you can buy to reduce the voltage to your appliances. Get ahold of a local electrician and explain the problem. I'm sure you'll be able to get some help. You can use 110v appliances in countries that use 220v, IF you have an adapter (step down transformer) ... you cannot plug them directly into the 220v source for several reasons: 1. The plugs won't match up as the power plug configurations are much different 2. The appliances will literally blow up of catch on fire if you exceed the voltage limit specified on their labels. If you have moved permanently to India and are staying there, it might be in your best interests to buy new appliances.
Can you run a 110v heater on 220v circuit?
No.It'll overload and fail just about immediately.It's possible - but not recommended - to run two 110 v heaters in series from a 220v circuit.
If you plug a 1000 w portable heater into a 220v outlet will it burn out?
you must check the voltage and current rating for the heater, the power itself doesnt matter Concur - Some heaters may be rated for the higher voltage which requires less current to run. Watts = Current * Voltage. You risk a fire if you try to run heater above its rated values which should be on a plate on the appliance.
Can you run a 60hz 110V motor on 50 hz 220V with a step down transformer?
NO dear we can not rotate a 110 vlolt motor on 220,but if your voltage is 110v then y can rotate it on 50hz ,no problem,but it will rotate at lower speed, ENGR. NASEER AHMED,PAKISTAN
What do you need to do to convert a 220V waterfall picture to 110V?
You need to acquire a 110V to 220V step-up transformer. Just be sure to take into consideration the frequency of the AC voltage. I believe the UK runs at 50 hz. and the US is at 60 hz. What that means to you is that the waterfall will run faster here in the States. Also be sure that the transformer's output will match the power consumption of the device you're going to power with it. Do they make such a device? Yes, but you can also use a 220V to 110V step-down transformer in reverse. (Providing it's just a transformer.)
Is there anyway to get 220V 60hz from a 110V 50hz power supply?
It would involve some electronics work but it could be done. Might add that it could be more expensive than just buying the proper power supply. Use Use 220V 60hz motor to run 110V 50hz Generator.
