0
Brazing either is very difficult, the two together is almost imposible as the two metals have differant melting points. It is far better where possible to use an epoxy compound and/or a joint into which the sepatare pieces will fit and can then be glued, Alternatively bond a piece of ss to the Ti and then braze them together.
What else can I help you with?
What equipment is required to braze metal?
Equipment to braze metal is commonly available in hardware stores and is sold in kits. Typically, it consists of a torch and several types of rods to braze metal. that is not what im looking for yea that is my question
Can I braze light galvanised steel to steel wire using a 'spitfire' propane torch of the kind with the long mixing nozzle?
You may be able to do this but it is not easy. The joining of the steel wire to the galanised part may not be sufficiently strong. It is difficult to braze anything except simple structures such as a straight pipe joints or flat pieces of metal with a propane torch. Keep in mind that welding galvanized steel is highly hazardous to your health because the galvanized coating has zinc that is dangerous to the lungs and respiratory system.
Is titanium is a semiconductor?
No, titanium is a metal.
What is mixed with titanium to make a mixture?
If you mixed titanium with anything, you would then have a titanium mixture.
What is atomic number of titanium in periodic table?
Ti stands for Titanium, therefore the number is 81.
How do you connect copper pipe?
YOU thread or braze copper pipe Copper tubling you solder, braze, flaire, compression ring, mechincal joints
Do you need pipe dope to connect brass pipe to copper pipe?
NO but you will need some type of sealent OR braze or soldering
How do you make reducer from pipe?
By placing a smaller pipe insider the larger one and weld /braze the gap
What is the best guaranteed leakproof sealant compound for joining galvanized pipe to the shower apparatus?
Teflon Pipe Dope. Guaranteed I would have to either weld or braze the piping together
Can you solder a hole in a pipe?
Copper you can. Treat it as you would any other connection, clean the area, surface and hole, get the moisture out and solder a patch over it. Small hole, you can just use solder or you can cut a small piece of pipe in half, clean and flux it and put it over the hole. Steel pipe, you can braze over the hole, same basic process as soldering, clean and fill with braze.
Difference between ss 321 and ss 304?
SS 321 contains titanium which makes it more corrosion resistant than SS 304. SS 321 is better suited for high temperature applications due to its improved resistance to intergranular corrosion. SS 304 is a general-purpose stainless steel with good overall corrosion resistance but not as high as SS 321.
Is it best to braze or sodier 24 gauge stove pipe?
If its made from tin then neither is appropriate. It should be riveted, or joined with self-tapping sheet metal screws.
How o make a pipe?
To make a lead or copper pipe all you need is sheet copper/ lead and either lead wipe /solder /braze the end or if copper use a Pittsburg found in sheet metal shops to make the seam
How do you braze a copper pipe end?
Brazing is a process used to join a gap in piping or other metal parts. It is technically impossible to do on only one end, since the way it works requires two sides to work in. Tried to answer this last night and was edited out. I'll try again While you can braze a copper pipe end, you usually don't. You solder it. Use whatever type of fitting on the end that you need. If you are just stopping the pipe, use a cap. Clean both the pipe the the inside of the cap with steel wool or fine sandpaper. Apply a coating of flux to each surface where they overlap and put the cap on the pipe. Heat one side of the cap with a propane torch and hold the solder on the opposite side. When the cap get hot enough to melt the solder, it will draw the liquid solder around the pipe to the flame. Once it does that, remove the flame and allow it to cool before messing with it. That's all there is to it. You could braze the cap to the pipe, but that would only connect the edge of the cap where it meets the pipe. The brazing rod would not melt between the whole cap as solder does. If absolutely had to, you could crimp the end together and braze the joint. That's the last resort.
How can I effectively braze a copper pipe for a secure and durable connection?
To effectively braze a copper pipe for a secure and durable connection, follow these steps: Clean the pipe and fittings thoroughly to remove any dirt, grease, or oxidation. Apply flux to the cleaned surfaces to prevent oxidation during the brazing process. Heat the joint evenly with a torch until it reaches the brazing temperature. Apply the brazing rod to the joint, allowing it to flow into the gap by capillary action. Allow the joint to cool naturally to ensure a strong bond. Inspect the joint for any leaks or imperfections before using the pipe.
What equipment is required to braze metal?
Equipment to braze metal is commonly available in hardware stores and is sold in kits. Typically, it consists of a torch and several types of rods to braze metal. that is not what im looking for yea that is my question
Do you have to braze 410a?
Yes, its a requirement of all manufacturers, that i know of, to braze 410a connections with a brazing alloy containing a minimum of 15%
