You shouldn't have to, 220 and 240 volts are a nominal figure in the same voltage range. It is brought about by the power company, as they have a responsibility to keep voltages within a certain 10% range. The load will only notice a difference of 1% on the load current. e.g. Wattage load of 2400. Amps = watts/volts. 2400/240V = 10 amps. 2400/220V = 10.9 amps. On a constant resistance as the voltage goes lower, the current goes higher and vice versa as the voltage goes higher, the current goes lower.
In Europe 240 volts is standard, so no a 115 volt motor will not work. In USA 120 volts is standard, so if your sub-panel has 120 volts, (check with voltage meter) then yes. Read carefully, To get 240 volts in a sub-panel in USA the electric company brings two (2) wires, each wire has 120 volts, 120 + 120 = 240. One of those 120 volts will run your motor. Look for the wires from the electric company and check them with your voltage meter. If this is a commercial application you will need to call an electrical contractor, power companies for commercial applications do not follow the above.
No. 240 Volts was the nominal standard in Australia with a tolerance of +/- 10%, So the voltage could be anywhere between 216 Volts and 264 Volts. The change to 230 volts is part of international harmonisation between countries that use 220 volt standards and 240 volt Standards. The new tolerance levels are +10% and - 6%.
A two pole, (220-240 volt) circuit breaker can go anywhere in a panel where it will physically fit, connecting to two poles on the buss bar. However, if you don't know this already, you probably shouldn't be fooling around in a live electrical panel. You can get seriously hurt or burned.
To convert 7620 volts to 240 volts, you would need to use a transformer. The transformer would step-down the voltage from 7620 volts to 240 volts. The ratio of the turns on the transformer primary and secondary windings determines the voltage transformation.
The TV might have a panel on the back where you can adjust the voltage that it works on. If not, you need a step-down transformer to convert 240 v to 120 v for the television, and it must be rated at the amount of power the TV takes, which could be 100-200 watts.
Oh, dude, it's like asking how many jelly beans are in a jar. A 200 amp panel typically runs on 240 volts in residential settings. So, like, if you're trying to power up your man cave or whatever, that's the magic number you're looking for.
In Europe 240 volts is standard, so no a 115 volt motor will not work. In USA 120 volts is standard, so if your sub-panel has 120 volts, (check with voltage meter) then yes. Read carefully, To get 240 volts in a sub-panel in USA the electric company brings two (2) wires, each wire has 120 volts, 120 + 120 = 240. One of those 120 volts will run your motor. Look for the wires from the electric company and check them with your voltage meter. If this is a commercial application you will need to call an electrical contractor, power companies for commercial applications do not follow the above.
voltage is the PUSH on electrons seriously 120 volts is the difference of 240...Simply said 240 volts is 2 times as strong as 120 volts.
In North America a two pole breaker will be used in the distribution panel for a supply of 240 volts for a 240 volt load.
240 volts maximum.
The standard voltage conversion ratio from 240 volts to 120 volts is 2:1.
No. 240 Volts was the nominal standard in Australia with a tolerance of +/- 10%, So the voltage could be anywhere between 216 Volts and 264 Volts. The change to 230 volts is part of international harmonisation between countries that use 220 volt standards and 240 volt Standards. The new tolerance levels are +10% and - 6%.
3.3 volts
only way to convert from 3 phase to 240 would be to change the electric motor on the compressor
To calculate the current in amps from power in watts and voltage, you can use the formula: Amps = Watts / Volts. Therefore, for 200 watts at 240 volts, the calculation would be 200 watts / 240 volts = 0.8333 amps. So, 200 watts is approximately 0.83 amps at 240 volts.
A two pole, (220-240 volt) circuit breaker can go anywhere in a panel where it will physically fit, connecting to two poles on the buss bar. However, if you don't know this already, you probably shouldn't be fooling around in a live electrical panel. You can get seriously hurt or burned.
To convert 7620 volts to 240 volts, you would need to use a transformer. The transformer would step-down the voltage from 7620 volts to 240 volts. The ratio of the turns on the transformer primary and secondary windings determines the voltage transformation.