answersLogoWhite

0

Answer for USA, Canada and countries running a 60 Hz supply service.

Do this electrical work only if you feel confident that you can do it safely. If not then this is the procedure that an electrician would use and you would be able to follow what he is doing. Again an electrician should be your first choice.

If you consider doing this the first thing is SHUT THE MAIN BREAKER OFF. Use an auxiliary light source to see when working in a dead panel. Always keep in mind an ARC FLASH ACROSS HOT MAINS HAS ENOUGH HEAT TO PEAL THE SKIN OFF OF YOU.

Before an explanation of how to do this you should keep in mind that this is for a single receptacle only. If any other receptacles are on the same circuit they will also be changed to 120 volts.

The existing two pole breaker in the distribution panel that is to be replaced should not have a larger rating than a 15 or 20 amps. The wire size from that breaker will be #14 or #12 respectively. The final results of this project will leave you with a 15 amp 120 volt receptacle and one spare 15 amp breaker in the distribution panel.

That said, OK, any 240 volt outlet can be changed to 120 volt by removing the white wire from the 2 pole breaker and inserting it into the neutral bus bar. Remove the other wire (probably black) from the breaker. Remove the 2 pole breaker from the breaker panel. Install two single pole 15 amp breakers into the hole left by the 2 pole breaker. Leave both of these breakers turned off.

Connect the black wire that came off of the 2 pole breaker on to one of the new single pole 15 amp breakers. Re install the cover to the electrical panel, this end is finished. At the old 240 volt receptacle, remove the existing device and install a new 120 volt receptacle.

Materials can be purchased at local building supply store. Remember to take the electrical panel data with you so you have the information for the 2 new breakers. Once you have the new 120 volt receptacle installed, identify on the electrical panel door what the breaker is used for. Leave the unused breaker in the off position. Turn the new 15 amp breaker on. Turn the main breaker back on. Test the new receptacle with a lamp to make sure every thing is OK.

As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.

Before you do any work yourself,

on electrical circuits, equipment or appliances

always use a test meter to ensure the circuit is, in fact, de-energized.

IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB

SAFELY AND COMPETENTLY

REFER THIS WORK TO QUALIFIED PROFESSIONALS.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Natural Sciences

What are some uses for an electrical cord?

Electrical cord is also refered to as power cord, line cord, and main cable. Electrical cord is mainly used to connect the appliance to the main electricity supply via wall socket.


What does T1 or T2 mean in electrical terms?

T1 and T2 commonly refer to the primary and secondary terminals of a transformer. T1 is typically the primary side where the input voltage is applied, while T2 is usually the secondary side where the output voltage is obtained. The terminals are used to connect the transformer to the electrical circuit.


How to split 220 to 110?

To split 220 volts into two 110-volt circuits, you will need a transformer that is capable of reducing the voltage from 220V to 110V. You would connect your 220V power source to the primary side of the transformer and then connect two separate circuits to the secondary side of the transformer to access the 110V output. Be sure to follow proper safety precautions and consult an electrician if you are unsure about handling electrical components.


Connecting a 240v to 24v 40va transformer?

To connect a 240V to 24V 40VA transformer, you will typically have two input wires for the 240V side and two output wires for the 24V side. The 240V input wires will connect to your power source, while the 24V output wires will connect to the device or circuit that requires the lower voltage. Make sure to follow proper wiring guidelines and safety precautions to avoid any electrical hazards.


Can you connect 400Volt oven to 230 Volt main?

No, a 400V oven cannot be connected directly to a 230V main electrical supply as they operate at different voltage levels. Doing so may damage the appliance or pose a safety hazard. It is recommended to have a licensed electrician assess the situation and install the appropriate electrical setup for the oven.

Related Questions

What are the steps involved in doorbell transformer installation?

The steps involved in doorbell transformer installation are: Turn off the power to the doorbell circuit. Locate the existing transformer or install a new one near the electrical panel. Connect the transformer to the power source using electrical wiring. Connect the transformer to the doorbell system using low-voltage wiring. Test the doorbell to ensure it is working properly. Secure the transformer in place and restore power to the circuit.


How can I hook up a doorbell transformer?

To hook up a doorbell transformer, first turn off the power to the area where you will be working. Locate the transformer near your electrical panel. Connect the transformer to a power source using electrical wire, making sure to match the wire colors. Then, connect the transformer to the doorbell system using low-voltage wire. Test the doorbell to ensure it is working properly before turning the power back on.


How can I properly install a doorbell transformer?

To properly install a doorbell transformer, first turn off the power to the circuit. Mount the transformer near the electrical panel. Connect the transformer to the circuit breaker and the doorbell wiring. Test the doorbell to ensure it is working properly.


What is the difference between a converter and an adapter?

A converter changes the electrical voltage of a device, while an adapter allows a device to physically connect to a different type of plug or outlet.


How do you make a 380v motor run on 220v?

Yes just connect any line to neutral you have 230volts already.


What is the difference between an adapter and a converter?

An adapter is used to connect different types of plugs or sockets, while a converter changes the voltage of an electrical device to match the power supply.


What are some uses for an electrical cord?

Electrical cord is also refered to as power cord, line cord, and main cable. Electrical cord is mainly used to connect the appliance to the main electricity supply via wall socket.


Why transformer does not rotate when its secondary is connected to bearing?

How do you connect the transformer's secondary to the bearings.


How do I properly install a doorbell transformer?

To properly install a doorbell transformer, first turn off the power to the circuit. Then, mount the transformer to a junction box near the electrical panel. Connect the transformer's wires to the power supply and the doorbell wires. Finally, turn the power back on and test the doorbell to ensure it is working correctly.


How can I install a doorbell transformer?

To install a doorbell transformer, first turn off the power to the area where you will be working. Locate the existing transformer and disconnect it. Mount the new transformer in a suitable location near an electrical outlet. Connect the wires from the transformer to the doorbell system according to the manufacturer's instructions. Finally, turn the power back on and test the doorbell to ensure it is working properly.


What does T1 or T2 mean in electrical terms?

T1 and T2 commonly refer to the primary and secondary terminals of a transformer. T1 is typically the primary side where the input voltage is applied, while T2 is usually the secondary side where the output voltage is obtained. The terminals are used to connect the transformer to the electrical circuit.


How do you wire a doorbell transformer correctly?

To wire a doorbell transformer correctly, connect the transformer's low-voltage wires to the doorbell system's power supply and the high-voltage wires to the electrical panel. Make sure to follow the manufacturer's instructions and turn off the power before starting the installation.