0
A BTU is the amount of energy required to raise the temperature of 1 pound of water 1 degree Fahrenheit (F) at or near 39.2 degrees F and 1 atmosphere of pressure.
Electric heaters are rated in KW, not BTU's
3413 BTU's = 1 KW-hr.
Check the link below for a PDF on water heater sizing.
What else can I help you with?
How many BTUs will a 10-kilowatt heater produce if operated for 1 hour?
A 10-kilowatt heater produces 34,120 BTUs per hour.
How many BTUs in a 6 ft baseboard heater?
The number of BTUs in a 6 ft baseboard heater would depend on the model and specifications of the heater. On average, a 6 ft baseboard heater can generate around 1,000-1,500 BTUs per linear foot, so a 6 ft baseboard heater may produce approximately 6,000-9,000 BTUs.
What are the BTUs for the Lasko Electric Ceramic 1500 watt Tower Heater with remote control number 751320?
1500 watts is equivalent to 5118 BTU per hour. 1500 watt-hours is equivalent to 5118 BTU.
How many Btus must be removed from one pound of water at 200f fro it to end up as ice at 30f?
To determine the BTUs that must be removed from one pound of water at 200°F to convert it to ice at 30°F, we need to account for several steps: cooling the water from 200°F to 32°F (the freezing point), the phase change from water to ice at 32°F, and then cooling the ice from 32°F to 30°F. Cooling the water from 200°F to 32°F requires about 168 BTUs (1 BTU cools 1 pound of water by 1°F). Freezing the water at 32°F requires the removal of 80 BTUs (latent heat of fusion). Cooling the ice from 32°F to 30°F requires an additional 2 BTUs. In total, approximately 250 BTUs must be removed (168 + 80 + 2 = 250 BTUs).
How many amps will a 5200 btu heater pull?
To determine the amperage draw of a 5200 BTU heater, you can use the formula: Amps = BTUs / (Voltage x Efficiency). For example, if the heater operates at 120 volts and has an efficiency of about 100%, it would pull approximately 43.3 amps (5200 BTU / 120 volts). However, many small heaters operate at lower voltages (like 120V), so it's essential to check the specific heater's specifications for accurate amperage.
How many BTUs does it take to raise the temperature in a 40 gallon water heater 60 degrees F?
To calculate the BTUs needed to raise the temperature of a 40-gallon water heater by 60 degrees Fahrenheit, you can use the formula: BTUs = gallons × temperature rise × 8.34. For a 40-gallon heater, it would be 40 gallons × 60°F × 8.34 BTU/gallon°F, resulting in approximately 20,016 BTUs. Therefore, it takes about 20,016 BTUs to achieve that temperature increase.
How many BTUs will a 10-kilowatt heater produce if operated for 1 hour?
A 10-kilowatt heater produces 34,120 BTUs per hour.
What is the Gallon Per Hour use of a kerosene heater?
Depends on the BTUs of the heater.
How many btus per foot of baseboard?
The number of BTUs per foot of baseboard heating can vary depending on the type and size of the baseboard unit. Typically, standard hydronic (hot water) baseboard heaters emit around 400 to 600 BTUs per foot, while electric baseboard heaters can produce about 250 to 300 BTUs per foot. The specific output also depends on factors like water temperature and the design of the heater. Always refer to manufacturer specifications for precise information.
How many btus in a 2000 watt heater?
2000
How many BTUs in a 6 ft baseboard heater?
The number of BTUs in a 6 ft baseboard heater would depend on the model and specifications of the heater. On average, a 6 ft baseboard heater can generate around 1,000-1,500 BTUs per linear foot, so a 6 ft baseboard heater may produce approximately 6,000-9,000 BTUs.
How many gallons of kerosene will a 400000 BTU forced air heater use?
To determine the gallons of kerosene a 400,000 BTU forced air heater will use, you need to know the energy content of kerosene, which is approximately 135,000 BTUs per gallon. Dividing 400,000 BTUs by 135,000 BTUs per gallon gives you about 2.96 gallons. Therefore, a 400,000 BTU heater would use roughly 3 gallons of kerosene for each hour of operation at full capacity.
How much will a 266 BTU pool heater raise your ccf usage on your gas bill?
To calculate how much a 266 BTU pool heater will raise your CCF usage on your gas bill, you need to determine how long the heater will run and the cost of gas per CCF. For instance, if the heater runs for 10 hours and uses 266 BTUs per hour, it will consume 2,660,000 BTUs in total. Since there are 100,000 BTUs in a CCF, this would equate to approximately 26.6 CCF. Multiply this by your local gas rate per CCF to estimate the increase in your gas bill.
What heater offers the most BTU's?
the Frost Fighter IHS #700 Indirect Space Heater ahs 700000 BTUs.
How long will it take for a 2kW heater to raise water 26000 BTU?
To determine how long it will take for a 2 kW heater to raise 26,000 BTU, you first need to convert BTUs to kilowatt-hours (kWh) since the heater's power is in kW. 26,000 BTU is approximately 7.64 kWh (1 BTU = 0.000293 kWh). Dividing the energy needed (7.64 kWh) by the power of the heater (2 kW) gives you about 3.82 hours. Thus, it will take approximately 3 hours and 49 minutes for the heater to raise the water by that amount.
How can I determine how many BTUs I need for an air conditioner?
A small room is about 5,000 BTUs. Most people don't have a room that would require more than 10,000 BTUs.
How many btu heater for 15x30 pool?
To heat a 15x30 pool, you'll generally need a heater with a capacity of around 100,000 to 150,000 BTUs. This range will efficiently raise the water temperature, depending on factors like the desired temperature increase, ambient conditions, and pool cover usage. It's essential to consider local climate and how often you plan to use the pool to determine the best heater size for your needs.
