The switch to open the fuel filler door is on the floorboard in front of the driver's seat. Pull up.
The gas filler door release lever on a 1997 Saturn 2 door is usually located on the driver's side, either on the driver's door panel or on the floor near the driver's seat. It may be a small lever or button that you pull or push to release the gas filler door. If you're having trouble finding it, refer to your vehicle's owner manual for specific instructions.
The door ajar switch on a 1993 Mercury Topaz is located in the door latch. The switch is triggered by the top hook of the latch. If the problem is having to frequently slam the door a second time to make the seat belt work, try to adjust the striker bolt attached to the door frame up a bit. Works for me.
Try checking the switches on the door frames. The switches are spring loaded; when you close the door it breaks the contact. Start with the driver's door. The driver's door receives the most use. Also: the switch can break and fall into the door pillar.
Turn on one light and leave it on for a little while then turn it off. Turn the next light on and open the door. Go up and feel the light bulbs..the warm one is the first loth switch,, the one that is still on is obviously the second light switch and the cold/regular temperature light bulb is the last switch that you didn't touch.
When a switch does not contain electricity, it represents an open circuit, meaning that the electrical current is not able to flow through the switch. This can be compared to opening a door, where the pathway is blocked and current cannot pass through.
There is no release, as such. All you have to do to open the fuel filler door is to press on the door and let go. It will pop open.
Toyota dealer parts department.
OPENING THE FUEL-FILLER DOOR To open the fuel-filler door, unlock the fuel-filler door by using one of the following operations, then push the right side of the door. Push the door handle request switch with the Intelligent Key carried with you. Push the UNLOCK button on the Intelligent Key. Insert the mechanical key into the door lock cylinder and turn it to the rear of the vehicle Push the power door lock switch to the UNLOCK position. To lock, close the fuel-filler door securely and lock all doors by operating the door handle request switch, the LOCK button on the Intelligent Key or the mechanical key.
To release the door for the gas filler, just press the outside rear of the door, it will spring open. The tank is protected by a lockable filler cap inside, that requires the ignition key.
Check in the trunk.
There is not a fuel door release lever on the 1994 VW Golf 3 door. Press on the front edge of the fuel door.
To open the fuel filler door on a 1999 Volvo V70, locate the fuel door release lever inside the vehicle, typically found on the driver's side near the seat. Pull the lever to release the door. If the lever does not work, you can manually push the fuel filler door to open it. Always ensure the vehicle is turned off and parked before refueling.
Geo Prizm door handles are the same 1993-1997
http://www.freepatentsonline.com/4917418.html -siv
The gas filler door release lever on a 1997 Saturn 2 door is usually located on the driver's side, either on the driver's door panel or on the floor near the driver's seat. It may be a small lever or button that you pull or push to release the gas filler door. If you're having trouble finding it, refer to your vehicle's owner manual for specific instructions.
The filler cap for a Mazda RX-8 is located on the driver's side of the vehicle, near the rear of the car. To access it, you need to open the fuel door by pressing the fuel door release button inside the cabin or by gently pushing on the fuel door itself. Once the door is open, you can unscrew the filler cap to refuel.
To replace the fuel tank filler door and controls on a 2001 Ford Explorer Sport, first, open the fuel filler door and remove the screws or clips securing it. Disconnect any electrical connectors for the fuel door release if equipped. Install the new filler door by reversing the removal process, ensuring it is securely fastened. Test the operation of the controls to ensure proper functionality.