answersLogoWhite

0

and breakers that can only hold up to 250 volts

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Natural Sciences

Is sj cord rated for 300 volts to be used for 480 volt?

No, SJ cord is only rated for 300 volts and is not suitable for use with 480 volts. It is important to use the correct voltage rated cord for safety and to prevent damage to equipment. Look for cords that are specifically rated for 480 volts.


Where is the sensor circuit high volts locat?

The sensor circuit high volts is typically located near the sensor that is monitoring high voltage levels. It is important to ensure the sensor circuit is properly designed and installed to accurately detect and measure high voltage levels to prevent any potential damage or danger.


What occurs when the incoming electrical power increases significantly above the normal 120 volts?

When the incoming electrical power increases significantly above 120 volts, it can lead to damage or malfunction of electrical devices connected to the circuit. This overvoltage condition can cause overheating, insulation breakdown, and potential fires in the electrical system. To prevent damage, surge protectors or voltage regulators can be used to stabilize the electrical supply.


You observe a small plaque on an electrical appliance that reads in part 115 volts AC 60 Hz This means that the appliance?

That the appliance does not need a electrical transformer and uses the US standards for electricity off the grid.


What is the typical line voltage for gas furnaces?

The typical line voltage for gas furnaces is 120 volts for residential units and 240 volts for commercial units. This voltage powers the components such as the blower motor, ignition system, and controls in the furnace. It is important to ensure the voltage is compatible with the furnace to prevent damage or malfunction.

Related Questions

How many volts can damage an electronic component?

30 volts of ESD


Is sj cord rated for 300 volts to be used for 480 volt?

No, SJ cord is only rated for 300 volts and is not suitable for use with 480 volts. It is important to use the correct voltage rated cord for safety and to prevent damage to equipment. Look for cords that are specifically rated for 480 volts.


What are the specific electrical requirements for a device that operates on 208 volts single phase power?

A device that operates on 208 volts single phase power requires a power source that provides 208 volts of electricity in a single phase. It is important to ensure that the device is compatible with this specific voltage to prevent damage or malfunction.


How can you make a bypass diode?

the diode is forward bias ANSWER: A bypass diode is used to bypass circuitry as soon as the diode is forward bias by 0.6 volts The use it to bypass to prevent damage to the circuitry


Where is the sensor circuit high volts locat?

The sensor circuit high volts is typically located near the sensor that is monitoring high voltage levels. It is important to ensure the sensor circuit is properly designed and installed to accurately detect and measure high voltage levels to prevent any potential damage or danger.


What occurs when the incoming electrical power increases significantly above the normal 120 volts?

When the incoming electrical power increases significantly above 120 volts, it can lead to damage or malfunction of electrical devices connected to the circuit. This overvoltage condition can cause overheating, insulation breakdown, and potential fires in the electrical system. To prevent damage, surge protectors or voltage regulators can be used to stabilize the electrical supply.


What is programmable output in voltage regulators?

A: The output voltage a 7805 can becomes a 1 voltage regulator of higher voltage the 5 volts if so chosen. However it can never becomes less then 5 volts not unless a negative voltage source is found.


Is it dangerous for 12volt battery to have 13.5 volts?

A 12-volt battery is designed to operate around 12 volts, but it can safely tolerate voltages up to about 13.5 volts, especially when charging. However, if a battery consistently exceeds this voltage, it may indicate overcharging, which can lead to overheating, damage, or reduced lifespan. It's important to monitor the battery's condition and ensure that charging systems are functioning correctly to prevent potential hazards.


When i plugged 110 volts wii into 220 volts socket smoke came out of the ac adaptor did i damage the console?

No way of telling, but you certainly fried the AC adaptor.


Why plus 24 volt is used for telecom equipments?

+24 volts is not normally used for telecom equipment. -48 volts is the usual value. 48 was chosen as a compromise between safety and voltage/power efficiency. Minus was chosen over plus to manage corrosion effects of cabling in underground installations.


What potential will you have with 120 volts and 277 volts in same encloser?

The potential for someone to come along later on and get the wires mixed up causing damage to electrical appliances or lights.


Can you power a 3 phase 240 volts 20 ton air condition unit using the voltage settings 1 phase 127 volts 2 phase 127 volts and 3 phase 127 volts where between any two phases the voltage is 240 v?

If you have a voltage of 127 volts to neutral (ground) then your wye connected three phase leg voltages will have to be 127 x 1.73 = 220 volts. This voltage is within the 10% allowance for voltages as should operate the compressor. As the voltage is lower that specified, the amperage rating when a reading is taken will be higher than that of the equipments nameplate.