<><><>
Three-wire dryer outlets are generally composed of two hots and a grounded conductor. This grounded conductor may either be insulated, in which case it is the intentionally grounded "identified" conductor or neutral, or bare, in which case it is the grounding conductor.
In either case, the grounded conductor will provide a ground path for the equipment frame connected to it.
The obvious limitation in this scenario is the adequacy of the circuit to supply the device, in this case a welder.
Bear in mind that there is no such device as a "dryer outlet." That is simply the device's most common use, hence the name. It's proper name/description is a NEMA 10-30R receptacle.
<><><>
Canada uses NEMA 14-30R which has both neutral and Ground as well as 2 hot wires, so could potentially be plugged in as long as the welder is not rated more than 30 amps. But as a general rule of thumb, if you can't plug it in without modifying any part of the circuit, then the answer is no, it can't be done. Also these circuits are dedicated so only one thing can be on the line.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
If you are connecting a 4-prong dryer cord to a 3-prong outlet, the extra ground wire (green or bare copper wire) should be left unconnected. Do not try to ground it by connecting it to the neutral terminal or anywhere else. This is to prevent creating a ground loop and potentially causing a safety hazard.
My question is WHY did you replace a four prong dryer plug with a three prong! 220 volt Electric dryers require two hot legs, a neutral and a system ground wire. Sounds as though you shunted one of the hots or the neutral. You need to install a four prong plug of the same configuration and wire it exactly as the original.
First you need to know that an electric dryer is almost always a 30 amp 220 Volt power supply. Most small welders require a 50 amp 220 volt power supply. Check your welder's power requirement. If it requires 50 amps, it'll never work correctly on 30 amp.The plug conversion is simple. The wire your dryer is powered by will have two "hot" legs, the red and black wires. These supply the 220 volt. Then it has a ground (bare copper or green conductor. And last it has a white wire, the neutral.Your 3 prong plug on your welder only requires the two "hot" legs and the ground wire. You shunt the neutral white wire with a wire nut.
Do not use this type of cable to feed a 120/240V dryer outlet. The outlet is ungrounded, and the third conductor is neutral not ground. Your ground wire must be sheathed by code. You cannot use the bare neutral conductor as ground. Diagram Did Not Come Through. You Have a 3 Prong Connector. The Prong On The Bottom By Its Self Connect The Bare Wire. That Is What Was # 3 Connect The Others To The Two Prongs Next To Each Other. Hope This Makes Some Sense (1) (2) (3) Connect White To (1), Connect Black To (2) Bare (3) Good Luck
Ground wire
If you are connecting a 4-prong dryer cord to a 3-prong outlet, the extra ground wire (green or bare copper wire) should be left unconnected. Do not try to ground it by connecting it to the neutral terminal or anywhere else. This is to prevent creating a ground loop and potentially causing a safety hazard.
My question is WHY did you replace a four prong dryer plug with a three prong! 220 volt Electric dryers require two hot legs, a neutral and a system ground wire. Sounds as though you shunted one of the hots or the neutral. You need to install a four prong plug of the same configuration and wire it exactly as the original.
To wire a 3 prong dryer outlet correctly, connect the ground wire to the green screw, the neutral wire to the silver screw, and the hot wire to the brass screw. Make sure to turn off the power before starting and follow the manufacturer's instructions for your specific dryer model.
To hook up a 3 prong dryer cord correctly, first make sure the dryer is unplugged. Then, connect the neutral wire to the center terminal, the hot wire to the left terminal, and the ground wire to the right terminal. Tighten the screws securely and plug in the dryer to test it.
The correct wiring diagram for a 3 prong dryer cord is to connect the neutral wire to the center terminal, the hot wire to the left terminal, and the ground wire to the right terminal. Make sure to follow the manufacturer's instructions for your specific dryer model.
To wire a 4 prong dryer plug correctly, connect the green wire to the ground screw, the white wire to the center terminal, the black wire to one of the side terminals, and the red wire to the other side terminal. Make sure to tighten the screws securely and follow the manufacturer's instructions for your specific dryer model.
To properly wire a 3 prong dryer outlet, connect the ground wire to the green screw, the neutral wire to the silver screw, and the hot wire to the brass screw. Make sure to turn off the power before starting and follow the manufacturer's instructions carefully.
First you need to know that an electric dryer is almost always a 30 amp 220 Volt power supply. Most small welders require a 50 amp 220 volt power supply. Check your welder's power requirement. If it requires 50 amps, it'll never work correctly on 30 amp.The plug conversion is simple. The wire your dryer is powered by will have two "hot" legs, the red and black wires. These supply the 220 volt. Then it has a ground (bare copper or green conductor. And last it has a white wire, the neutral.Your 3 prong plug on your welder only requires the two "hot" legs and the ground wire. You shunt the neutral white wire with a wire nut.
The correct 3 prong dryer outlet wiring diagram includes connecting the neutral wire to the center terminal, the hot wire to the left terminal, and the ground wire to the right terminal. This setup ensures safe and efficient installation of the dryer outlet.
The second ground prong grounds the frame and shell of the dryer. You can attach it anywhere on the frame if there is not a specific terminal for it, or just ignore it. The two hot and 1 ground should let it function. Do not ignore the green wire or grounding conductor. Remove the bonding jumper from the neutral terminal (grounded conductor, white wire) that bonds the neutral to the metal frame. The screw on the metal frame of the dryer the bond strap connects to is where you want to land the green wire. Save the bond strap you might have to convert it back to three wire in the future.
Do not use this type of cable to feed a 120/240V dryer outlet. The outlet is ungrounded, and the third conductor is neutral not ground. Your ground wire must be sheathed by code. You cannot use the bare neutral conductor as ground. Diagram Did Not Come Through. You Have a 3 Prong Connector. The Prong On The Bottom By Its Self Connect The Bare Wire. That Is What Was # 3 Connect The Others To The Two Prongs Next To Each Other. Hope This Makes Some Sense (1) (2) (3) Connect White To (1), Connect Black To (2) Bare (3) Good Luck
The 3-prong dryer plug wiring diagram involves connecting the green wire to the ground screw, the white wire to the center terminal, and the black wire to either of the outer terminals. Make sure to follow safety precautions and consult a professional if needed.