0
You can't. Two 4 ohm speakers in parallel equal 2 ohms, and two in series equal 8 ohms. It is possible to wire four 4 ohm speakers so that the load is 4 ohms though. Put two in series (8 ohms). put the other two in series (8 ohms). Then put the two sets in parallel (two 8 ohm sets in parallel equal 4 ohms).
What else can I help you with?
How do you wire floating neutral in sub panel?
You need to be more specific. Is this your feed?? Is this a home run (the wire that is feeding a circuit). Anyway if this is your feed wire (the wire supplying power to your sub panel) then you will land your two hots , then you will land your ground wire on the lug that is bonded to the panel. Sometimes this is a ground bar that can be screwed to the panel itself and then your neutral will go to the bar that is not touching anything. So your neutral coming in will be tightened down to the same bar as the neutrals that are feeding the circuits. This is assuming you'r are feeding your sub panel with 2 hots, a ground and a neutral.
Can you use 4 AWG wire with a 6 AWG ground wire to a sub box 100 feet away?
Yes you can. You did not say how many amps were required.
How do you hook up a 4 wire double pole box from the power of a sub box with no neutral BUS?
If you have a "sub box" with no neutral supplied to it, then you can't safely wire a four lead receptacle as you can't provide the needed neutral, the grounded conductor, to the device your feeding.
What wire is required for a 60A sub panel off a 150A main service?
For a 60A sub panel, you would typically use 6 AWG copper wire or 4 AWG aluminum wire to connect it to a 150A main service. Make sure to consult local electrical codes and regulations to ensure compliance.
Can you feed a 60 amp sub panel from another 60 amp sub panel?
Yes, you can feed a 60 amp sub panel from another 60 amp sub panel as long as the total connected load does not exceed 60 amps. Make sure to properly size the wire and protect the circuits with appropriate breakers to ensure safe operation of the sub panel.
Correct way to hook up pioneer 12Ins sub woofer's champion series?
Depends if it is dual 4Ohm or dual 2Ohm and what Impedance your Amp supports. *If you amp can handle 1Ohm Load and you have a dual 2Ohm sub you can run the sub in parallel to get a 1Ohm load (parallel meaning both + are connected with each and same with both -) *If your amp can handle 2Ohm load and you have a dual 4Ohm sub you can run the sub in parallel to get a 2Ohm load. *If your amp supports a 4Ohm load and you have a dual 2Ohm sub you can run the sub in series to get a 4Ohm load. (series meaning the - from one coil is to be connected with the + on the other coil) Do not mix up Impedance's make sure you find out what your Subs Impedance is and what you Amps Impedance is
How do you wire dual voice coil 4ohm?
you don't light the car on fire and make it explode
What information does the sub panel wire size chart provide for determining the appropriate wire size for a sub panel installation?
The sub panel wire size chart provides information on the recommended wire size based on the amperage of the sub panel, the distance the wire needs to run, and the type of wire insulation. This helps determine the appropriate wire size for a sub panel installation to ensure safety and efficiency.
How do you wire a sub in a Saturn sc?
Connect the sub woofer to the equalizer or amplifier. The positive wire will need to be connected to a power source. Connect the ground wire. Connect the auxiliary wire to the amplifier.
Where do you wire the power cable in Corsa?
to wire it through a corsa, strip one end and connect to sub or amp, then the other end runs through the car. unscrew the glove box and wire it through thegrommet behind the battery under the bonnet to the positive terminal. Fuse connector half a meter down the wire does help the sub or amp to cope with the current and lessens the chance of blowing your sub
What size wire should be used for a sub panel installation?
The size of wire needed for a sub panel installation depends on the amperage of the sub panel. It is recommended to consult with a licensed electrician to determine the appropriate wire size for your specific installation.
What is the recommended wire size for a 60 amp sub panel installation?
For a 60 amp sub panel installation, the recommended wire size is typically 6-gauge copper wire.
What is the recommended ground wire size for a 100 amp sub panel installation?
The recommended ground wire size for a 100 amp sub panel installation is typically 8 copper wire.
What is the recommended wire size for a sub panel installation?
The recommended wire size for a sub panel installation is typically determined by the amperage of the sub panel. It is important to consult the National Electrical Code (NEC) or a qualified electrician to determine the appropriate wire size for your specific installation.
What information can I find in the 100 amp sub panel wire size chart?
The 100 amp sub panel wire size chart provides information on the recommended wire sizes for different distances and types of wiring to safely and efficiently supply power to a 100 amp sub panel.
Bridge two subs to a four channel amp?
If you amp is bridgeable you run + sub wire to ch 1 + then the -sub wire to the - of ch 2 of the amp. The same with the other sub + ch3 - ch4 that's how to bridge your amp.
Will a 540 Watts x 1 RMS 4ohms Amplifier be suitable for a sub rated at 380 watt RMS with 4ohms plus 4ohms dual coil?
The problem you have there is that your sub woofer needs both coils wired and your options with that setup is either 2 ohms or 8 ohms depending on if you wire the sub itself in series or parallel. If you use a second sub like the first one and wire both subs in parallel and then wire the two subs in series you can achieve 4 ohms. You could also wire the subs in series ( 8 ohms each ) and then wire them in parallel to achieve the overall 4 ohms.
