answersLogoWhite

0

To test the pH of the saliva and the guess the pH of the entire body is not a logical concept. You better take the blood sample and get the pH tested for the same. It is very accurate method to detect the pH of the body. The pH of the saliva may get acidic due to starchy food you have eaten before the examination of the saliva.

User Avatar

Wiki User

10y ago

What else can I help you with?

Continue Learning about Natural Sciences

How do you measure elongation of tension specimen?

The elongation of a tension specimen can be measured by marking a gauge length on the specimen before testing it and then comparing the final length of the specimen after it has been stretched to the original gauge length. The elongation can be calculated using the formula: Elongation = ((final length - original length) / original length) x 100%.


Can you run two 14 gauge wires tied together side by side to make it 10 gauge?

In the United States this is a violation of code. Of course you can physically do it. But the code does not allow parallel conductors any smaller than 1/0 unless each individual conductor is large enough to handle the entire circuit. Using 14 gauge wire you would have to have a circuit no larger than 15 amps, regardless of how many wires you parallel.


What is Altitude gauge?

An altitude gauge is an instrument that measures the vertical distance above a reference point, usually in relation to sea level. It is commonly used in aircraft to provide pilots with information about the altitude of the aircraft in flight.


What wire gauge should be used for 9 amp maximum?

A wire gauge of 16 AWG is typically suitable for a maximum current of 9 amps. However, you may also consider using a gauge of 14 AWG to provide some extra margin for safety and reduced voltage drop over longer distances.


What wire gauge do you need for a small electric welder when runnung for a distance of 35 feet?

For a small electric welder operating at 120V and up to 20A over a distance of 35 feet, a wire gauge of 10 AWG would be suitable to minimize voltage drop. This gauge ensures efficient power transmission and safe operation for the welder.

Related Questions

Where a pressure gauge would be used?

checking the tires testing fuel pump pressure testing fuel pressure regulator testing compression testing the coolant system testing engine oil pressure testing transmission pump pressure


Testing the discharge pressure gauge begins by?

Testing the discharge pressure gauge begins by ensuring that the system is safely shut down and depressurized. Next, the gauge is isolated from the system, often using valves, to prevent any fluid from affecting the measurement. A calibrated pressure source is then connected to the gauge, and the readings are compared against the known pressure value to determine accuracy. Any discrepancies may indicate the need for recalibration or replacement of the gauge.


Why does a hydraulic technician use gauge pressure when testing a hydraulic circuit?

For measuring the flow of hydraulic fluid.


Does a Chrysler Town and Country tachometer have a fuse?

Yes, it would be the same fuse that feeds the entire gauge cluster.


How do you fix gas gauge in 1999 izuzu rodeo the light stays on and gauge needle goes back and forth?

on my 99 rodeo, this problem was caused by the fuel indicator located inside the fuel tank and part of the pump - you need to replace the entire pump which entails dropping the entire tank


When was the 220a 16 gauge shot gun made?

You will have to provide the name of the maker.


What year is a browning with ser 348476?

You must provide the model and caliber/gauge.


1992 Astro Digital Temp Gauge pegged out Looking for color codes or location of Tempsensor since Friend messed with the starter and worked under the dash -the gauge worked fine before.?

Follow the wire from your gauge and you'll find it's grounded at some point, this is the only reason a gauge will peg. (This is also a great way of testing any gauge, ground it and if the gauge pegs it's good, if it doesn't it's bad)


What service does the company 0 Gauge provide?

O Gauge provides items that are related to toy trains and railroading. An actual O Gauge is used as a scale for these types of activities. The company will ship to its customers.


What is thicker A.30 gauge PVC or B.32 gauge PVC?

A. 30 gauge PVC is thicker than B. 32 gauge PVC. In gauge measurements, a lower number indicates a thicker material, so 30 gauge has a greater thickness compared to 32 gauge. Therefore, if you're comparing the two, 30 gauge PVC will be more durable and provide more resistance to wear and tear.


How much urine is required in a drug test?

For a DOT test 45ml. For a drug free workplace test 30ml. If you are doing an immediate test enough so it can be read on the temperature gauge and then the test is to be put inside cup, then urine soaks into test and test lines must all be clear enough to read. If all lines are there it is negative (this is good).


Fuel gauge not working on your 73 Chevy truck?

Either the sender wire is bad, or the sender inside the fuel tank is bad. Here is how to test it. Ground the wire that runs from the tank. This should pin the gauge all the way to full. If this happens, it is the sending unit. No gauge movement means bad gauge. Remember to turn on the key while testing.