The number of can lights that can go on one breaker will depend on the wattage of each light and the maximum load capacity of the breaker. It's important to calculate the total wattage of all the lights and ensure it does not exceed the amp rating of the breaker to avoid overloading it. Consult with an electrician to determine the appropriate number of can lights that can safely go on one breaker.
The number of fan and light sets you can put on one breaker depends on the breaker’s amperage and the wattage of the devices. Generally, a 15-amp breaker can handle about 1,800 watts, while a 20-amp breaker can handle about 2,400 watts. You'll need to calculate the total wattage of your fans and lights combined and ensure it stays within 80% of the breaker's capacity for safety. It's also important to consider the specific electrical codes and guidelines applicable to your area.
Hopefully just the black wires are on the breaker. Two circuits on one breaker. Shouldn't be a problem. It would depend on how many outlets or lights were on the breaker in total. Even then, there is very little chance of something drawing current from every outlet at the same time. The only thing is you can't put two wires under one breaker (by code). You would have to wire nut them with a pig-tail then just put the one wire under the breaker.
Ok, lets assume that these are not newly installed lights or lights added to this already existing circuit first what type of lights are they? the reason I asked is because if they are fluorescent lights it could be a faulty ballast. if it's regular light bulbs then they are several things to look for. how many lights on this breaker? have you placed a higher wattage bulb in these lights than recommended? what is your combined wattage? a 15 amp breaker is rated to supply power safely up to a maximum of 1440 watts. add up the wattage of each light bulb including any outside flood lights or outlets also on this circuit. If the the total is under 1440 watts then first replace the breaker with the same wattage rating then turn each light one at a time and wait to see if the breaker trips again. If it does, check the last light you switched on. Answer for USA: Never load a breaker to its full rating. The law allows only 80 percent of the breaker rating. That's the 1440 watts for a 15 amp breaker, and 1920 watts for a 20 amp breaker. Also look for a load you might not think is on the breaker, such as an outdoor light, or something in a hall or another room. Other causes: - A motor draws more current when it starts than when it runs. - An aging breaker, or one that has been overloaded too many times, can trip at a reduced current. If this is the case, it needs to be replaced.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any workANDalways use an electricians test meter having metal-tipped probes(not a simple proximity voltage indicator)to insure the circuit is, in fact, de-energized.
You would need one 30 amp double-pole breaker in the breaker box for a 240V cooktop.
The circuit breakers in a panelboard feed separate circuits. The lights that stay on are on a different circuit than the ones that go off. To fine the circuit that feeds the lights that stay on, go to the panelboard and turn off the breakers one by one until the lights go out. This is the circuit that feeds that circuit of lights. Remember that lights and receptacles can be on the same circuit together.
Canned lights and recessed lights are essentially the same thing, with "canned lights" being a colloquial term for recessed lights. Both types of lights are installed into the ceiling, providing a sleek and modern look. They are suitable for spaces where you want a clean and unobtrusive lighting solution.
I really need more detailed information to answer your question. How many lights were added and what wattage bulbs are being used? For a 15-amp breaker, the maximum wattage it would handle would be around 1650 watts. This would be about 16 100-watt bulbs. Does your breaker trip immediately when you turn the light switch on? If you have an ohmmeter you can check the tripped breaker. Put one lead on the black "hot" wire coming from the breaker. Remember, the breaker must be off. Then put the other lead on the ground bar. If the ohm reading is very low, close to 2 ohms, then you have a direct short to ground somewhere in your wiring.
150
Pot lights? I will guess recessed ceiling lights? I would look at the one that shorted to see if it is the first one in the series and lost the connection. The switch may also be the problem.
It means the breaker has been tripped. There are two possible ways to reset it - some have a button on the outlet (there may be several outlets on one circuit, so you may have to look around) the other is the main breaker in your breaker box. You'll need to find a reset the breaker.
The number of fan and light sets you can put on one breaker depends on the breaker’s amperage and the wattage of the devices. Generally, a 15-amp breaker can handle about 1,800 watts, while a 20-amp breaker can handle about 2,400 watts. You'll need to calculate the total wattage of your fans and lights combined and ensure it stays within 80% of the breaker's capacity for safety. It's also important to consider the specific electrical codes and guidelines applicable to your area.
could be bad circuit breaker
There are 31 carbs one cup (5.8 oz or 164g) of canned, drained, corn. .
Hopefully just the black wires are on the breaker. Two circuits on one breaker. Shouldn't be a problem. It would depend on how many outlets or lights were on the breaker in total. Even then, there is very little chance of something drawing current from every outlet at the same time. The only thing is you can't put two wires under one breaker (by code). You would have to wire nut them with a pig-tail then just put the one wire under the breaker.
There are many places where one can go online to find out information about how fruit is canned. One can visit popular on the web sources such as Wegmans and Del Monte Foods to find information about how fruit is canned.
The bulbs are in connected series. There was a short circuit and the circuit breaker tripped.
Ok, lets assume that these are not newly installed lights or lights added to this already existing circuit first what type of lights are they? the reason I asked is because if they are fluorescent lights it could be a faulty ballast. if it's regular light bulbs then they are several things to look for. how many lights on this breaker? have you placed a higher wattage bulb in these lights than recommended? what is your combined wattage? a 15 amp breaker is rated to supply power safely up to a maximum of 1440 watts. add up the wattage of each light bulb including any outside flood lights or outlets also on this circuit. If the the total is under 1440 watts then first replace the breaker with the same wattage rating then turn each light one at a time and wait to see if the breaker trips again. If it does, check the last light you switched on. Answer for USA: Never load a breaker to its full rating. The law allows only 80 percent of the breaker rating. That's the 1440 watts for a 15 amp breaker, and 1920 watts for a 20 amp breaker. Also look for a load you might not think is on the breaker, such as an outdoor light, or something in a hall or another room. Other causes: - A motor draws more current when it starts than when it runs. - An aging breaker, or one that has been overloaded too many times, can trip at a reduced current. If this is the case, it needs to be replaced.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any workANDalways use an electricians test meter having metal-tipped probes(not a simple proximity voltage indicator)to insure the circuit is, in fact, de-energized.