0
The force required to turn off a light switch is typically quite small, usually in the range of 1 to 5 newtons, depending on the design of the switch. Most light switches are designed for easy operation, allowing users to toggle them with minimal effort. In practice, the actual force needed can vary based on the switch's mechanism and condition.
What else can I help you with?
How can i take power from exsisting light switch to another light and switch for another room?
Only if the existing switch box has an unswitched hot and neutral in it.
How much work does it take to turn a light switch on?
Not much work at all, just go to the switch and flip it up. As for how much energy does it take, that is a different matter.
Have 3 lights Power to light 1 Need to connect light 2 then light 3 then down to single pole switch How do you wire?
You would wire the switch to the first light. Code says to break the black or power side of the circuit. Connect the white to the light. Take the black down to the switch on the black wire and back to the light on the white. This is a line of wire from the light to the switch. From the first light, take the white and the return white from the switch to the second with another run of wire. This will be regular black white with ground. White to white and at the first light the return line from the switch is white but hook to the black to the second light. Second light to third just continues the two wires. Black to black, white to white. I think this is clear enough to follow. If not, ask again.
How do you wire a 220 volts light?
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
Why does a wall switch 'crackle' and the light flicker?
There is a high current draw on the circuit and the switch is getting old. Change out the switch, see if you can find a 20 amp switch as the internal contacts are designed to take the higher amperage. Check how many lamps are in the circuit in watts, add them together and use the formula for amps. Amps = Watts/Volts (120).
How many people do you need to turn on a light bulb?
It should only take one person to switch on a light bulb if it is 6 light bulbs it may take 6 people to switch on a light bulb Der!
Can you power a light switch power to switch then to light from a switch beside the one you want hot the switch that you want to take power from has the white as hot switch after light?
I can not understand your question.
How do you take the head light dome light switch off on a 1993 Mercury Cougar?
You don't. The switch is all one , you will have to replace the entire switch.
How can i take power from exsisting light switch to another light and switch for another room?
Only if the existing switch box has an unswitched hot and neutral in it.
How many newtons dose it take to equal 1 lb of thrust?
1 pound-force = 4.445 newtons (rounded)
Turn on light house light in Poptropica?
Take the lobster claw and turn the switch.
How many Mexicans does it take to switch a light bulb?
1001, 1000 to turn the house, and 1 to hold the lightbulb in place.
How many people does it take to switch a light bulb?
It takes three. Two to hold the bulb and one to hold the whip.
How do you change the brake light switch on a 1994 silverado?
Take hold of the brake light switch and pull backwards. The switch will come out in the same way that you would unplug anything. Plug the new switch in
Why does the bulb not light up until you press the switch?
the bulb will light up when current flows thru it if the switch is open no flow will take place
How do you replace the stop light switch on a 97 Avalon you already bought the part you need help getting the one that in there out?
The 1997 Toyota Avalon stop light switch simply plugs in and out. Take hold of the stop light switch and pull outward. Plug the new stop light switch in.
Dome light will not go out on 1997 BMW 318?
Take the light out. You might have a bad switch in the door frame. When the door closes- it pushes a switch which I believe opens a circuit and shuts off your light. If the switch is bad it wont open the circuit and the light stays on.
