answersLogoWhite

0

an inside micrometer

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Natural Sciences

What is mean by NB in using valve measurement?

NB stands for "Nominal Bore" and refers to the nominal size of the valve in a piping system, typically measured in inches. It represents the internal diameter of the valve or pipe. It is an important parameter used to select the right valve for a specific application.


When is the next tidal bore on the River Dee in flintshire?

The next tidal bore on the River Dee in Flintshire is dependant on the tide cycle and specific conditions. It is advised to consult a tidal bore prediction chart or local authorities for the most accurate information.


What are the four English words that have the same spelling but different meanings?

Fluke can mean: * A fish, and a flatworm. * The end parts of an anchor. * The fins on a whale's tail. * A stroke of luck. Close (near) and Close (close the door) Bore a hole in something A tidal bore (tide meets river, pushes water back upstream) A crashing bore (someone who puts you to sleep) Bore (a burden) past tense of the verb to bear Bat- a type of animal, or a bat used in baseball


What is the pH level of normal bore water?

The pH level of bore water can vary depending on factors like mineral content and surrounding environment. Generally, bore water has a pH level between 6.5 to 8.5, which is considered slightly acidic to slightly alkaline. Testing the pH of bore water is recommended to understand its specific characteristics.


Is the word bore a noun?

Yes, the word 'bore' is a noun, a singular, common noun; a word for:a drilling toola hole or passage made by use of a drillthe hollow part inside a gun barrel or other tubethe caliber of a firearma person whose talk or behavior is dull and uninterestingThe word 'bore' is also a verb: bore, bores, boring, bored.

Related Questions

What would you use to measure a valve guide bore?

Inside Micrometer


Where would a Full bore gate valve be used?

Generally speaking, gate valves in larger sizes are full bore unless you order a reduced port. You would always use a full bore gate valve for hot tapping purposes. or you would use a full bore gate vale for runinig a pig in pipeline.


What is the difference between reduced bore and full bore valve?

In Full bore ball valve, The bore dia will be same as internal dia of the pipe.In reduced bore, the bore dia is reduced than the ID of pipe.


Is the full bore applicable for gate valve or that's just for ball valve type?

For Ball valve only,as it gives more full bore flow,unlike wedge block,slow operating in Gate valve.


What is nb in valve?

NB is nothing but Nominal Bore.


What is mean by NB in using valve measurement?

NB stands for "Nominal Bore" and refers to the nominal size of the valve in a piping system, typically measured in inches. It represents the internal diameter of the valve or pipe. It is an important parameter used to select the right valve for a specific application.


Stevens Savage Corpoiction 410 Bore proor testes valve please'?

They would not generally release that information to the public.


Is full bore gate valve is different from normal gate valve?

valves are available in three types first is full bore equal to 100 percent opening normal bore/port equal to 80 percent opening reduced bore equal to 60 percent opening


What is a bore guide?

This is a tool used to align the cleaning rod with the bore so that it doesn't rub against the sides of the bore when you pull the cleaning rod in and out. This prevents damaging the bore during cleaning.


What do you measure a cylinder bore with?

Inside micrometer


Where to use reduced bore and full bore?

Use full bore for applications where pressure drop should be minimum (such as in the suction pipe of a pump with required NPSH very close to available NPSH), or for pipes which could be cleaned with a pig (so that the pig doesn't get stuck on the valve). In other applications a reduced bore should be OK.


1992 trx 250x a valve broke off damage to the head and piston did not hurt the cylinder can you just get it honed or does it need bored out?

If there was no damage to the cylinder bore then you will not need to bore it oversize.If there was no damage to the cylinder bore then you will not need to bore it oversize.