0
May a GFCI receptacle be installed as a replacement in an old installation where to 2 wire circuit has no equipment ground conductor?
Yes, a GFCI receptacle can be installed as a replacement in an old two-wire circuit without an equipment ground conductor. When doing so, the GFCI will provide ground fault protection, but it must be labeled as "No Equipment Ground." However, it's important to note that while the GFCI protects against ground faults, it does not provide a true equipment ground, so care should be taken when using appliances that require grounding.
What else can I help you with?
When you encounter a four-slot receptacle in a residential laundry room?
It allows for a separate equipment grounding conductor
Is it always necessary to attach the bare equipment grounding conductor of a nonmetallic-sheathed cableto the green hexagon-shaped grounding screw on a receptacle?
Yes, it is necessary to attach the bare equipment grounding conductor of a nonmetallic-sheathed cable to the green hexagon-shaped grounding screw on a receptacle. This connection ensures proper grounding, which is essential for safety by preventing electrical shock and reducing the risk of electrical fires. Proper grounding also helps protect equipment and improves the overall reliability of the electrical system.
Can you install a 277 volt receptacle in place of a 240 volt receptacle?
No. To prevent this sort of thing from happening, the 277 volt device and receptacle is physically larger that a 240 volt receptacle and will not fit in a regular receptacle junction box. For a 277 volt system the proper size junction boxes have to be purchased.
Is it always necessary to attach the bare equipment grounding conductor of a nonmetallic sheathed cable to the green hexagon shape grounding screw on a receptacle?
Yes, it is necessary to attach the bare equipment grounding conductor of a nonmetallic sheathed cable to the green hexagon-shaped grounding screw on a receptacle. This connection ensures that the grounding system is properly established, providing a safe path for fault currents and reducing the risk of electric shock. Proper grounding enhances the overall safety of the electrical system by preventing electrical hazards.
Can a duplex receptacle be installed in a non plenum ceiling cavity?
Yes they can. It can only be used for low voltage transformers that have that 6-32 screw in or mounted for a receptacle for service equipment .. like a/c unit or any serviceable equipment but no cords plugs plugged in Thu or above the ceiling sorry .
When you encounter a four-slot receptacle in a residential laundry room?
It allows for a separate equipment grounding conductor
May a GFCI receptacle be installed as a receptacle in an old installation where the 2-wire circuit has no equipment grounding conductor?
Actually, yes. The GFCI does not need any ground; it measures "leakage", i.e., an imbalance, regardless of whether there is "ground". The National Electrical Code permits installing a GFCI to replace a completely ungrounded receptacle. Others have said: No. The GFCI is designed to measure an unintended path to ground. Without a good ground reference this is not possible.
Is it always necessary to attach the bare equipment grounding conductor of a nonmetallic-sheathed cableto the green hexagon-shaped grounding screw on a receptacle?
Yes, it is necessary to attach the bare equipment grounding conductor of a nonmetallic-sheathed cable to the green hexagon-shaped grounding screw on a receptacle. This connection ensures proper grounding, which is essential for safety by preventing electrical shock and reducing the risk of electrical fires. Proper grounding also helps protect equipment and improves the overall reliability of the electrical system.
Can you install a 277 volt receptacle in place of a 240 volt receptacle?
No. To prevent this sort of thing from happening, the 277 volt device and receptacle is physically larger that a 240 volt receptacle and will not fit in a regular receptacle junction box. For a 277 volt system the proper size junction boxes have to be purchased.
Is it always necessary to attach the bare equipment grounding conductor of a nonmetallic sheathed cable to the green hexagon shape grounding screw on a receptacle?
Yes, it is necessary to attach the bare equipment grounding conductor of a nonmetallic sheathed cable to the green hexagon-shaped grounding screw on a receptacle. This connection ensures that the grounding system is properly established, providing a safe path for fault currents and reducing the risk of electric shock. Proper grounding enhances the overall safety of the electrical system by preventing electrical hazards.
What information can be found in the equipment grounding conductor chart?
The equipment grounding conductor chart provides information about the size of the conductor needed to safely ground electrical equipment based on the current rating of the circuit.
What information can be found in the equipment grounding conductor table?
The equipment grounding conductor table provides information about the size of the grounding conductor needed based on the type and size of the electrical equipment being used.
What is the difference between protective and functional earth?
protective earth (PE) is a conductor, other than a main earthing conductor, connecting any portion of the earthing system to the portion of the electrical installation. functional earth (FE) is an earthing arrangement provided to ensure correct operation of electrical equipment or to permit reliable and proper functioning of an installation
Can a duplex receptacle be installed in a non plenum ceiling cavity?
Yes they can. It can only be used for low voltage transformers that have that 6-32 screw in or mounted for a receptacle for service equipment .. like a/c unit or any serviceable equipment but no cords plugs plugged in Thu or above the ceiling sorry .
What is a piece of machinery or equipment that contains a pneumatic pressure energy source?
electrical receptacle
What does the National Electrical Code NEC say about running separate ground wires?
From the 2011 NEC, Section 250.130 states, in part, "For replacement of non-grounding-type receptacles with grounding-type receptacles...connections shall be permitted as indicated in 250.130(C)." Section 250.130 (C) states in its entirety, "(C) Nongrounding Receptacle Replacement or Branch Circuit Extensions. The equipment grounding conductor of a grounding-type receptacle or a branch-circuit extension shall be permitted to be connected to any of the following: (1) Any accessible point on the grounding electrode system as described in 250.50 (2) Any accessible point on the grounding electrode conductor (3) The equipment grounding terminal bar within the enclosure where the branch circuit for the receptacle or branch circuit originates (4) For grounded systems, the grounded service conductor within the service equipment enclosure" (5) For ungrounded systems, the grounding terminal bar within the service equipment enclosure" Now for some of my thoughts. It sounds like what you got was adequate. It was correct except for he should have used green or bare conductor, not white, unless he used green tape near the end of the conductor to designate it as green. This tape would be inside the box but I would have marked it outside the box also if it is visible. I would have run this conductor as close as possible and preferably attached to the existing circuit conductors. Looping the conductor as you have stated is not the best installation, in my view, but if you have at least 6 inches from the entry of the conductor to the grounding terminal and another 6 inches before it leaves the box, this is ok. The code does not require this 6 inches if the conductor isn't spliced but in your application it should be since, in my view, it should have been spliced. Solid or stranded is of no significance. While I have quoted the 2011 NEC in my answer, I do not expect this has changed any in recent years. The use of the word "bonding" by your electrician was technically incorrect but "bonding" and "grounding" are sometimes used synonymously. They are different but often look alike to the untrained eye. Even electricians often misuse these terms and fail to understand the difference. It takes someone like myself who is a little anal retentive to use the terms properly. I hope you will acknowledge my answer as I am particularly interested to know if you got it.
Is a receptacle safe to use after an electrical arc?
Most of the times yes. If it is an appliance that gets pulled out of a receptacle under load and there is a small arc produced this will not damage the receptacle. It will pit the blades inside the receptacle but not enough to render the receptacle unserviceable It is not recommended to use this method to disconnect electrical equipment, use a switch in the circuit as they are designed to open a circuit under load.
