0
What else can I help you with?
How do i wire your robbins and Myers hunter ceiling fan after i have put the new flywheel on i wired the two black wires together as i had taped them for identification i now have two white wires do?
If you are not sure what wires where were it is best to call an electrician. In the US, the black is power, white neutral, and green ground.
Why are wires twisted together on a GFCI outlet box?
The ground wires are twisted together and then connected to the GFCI ground. The black and white wires may also be twisted together and then using a jumper wire connected to the GFCI. Hard to say without seeing exactly how it is wired.
Can groundwire be together with neutral wire at the dyer?
Ground and neutral should only be connected at the main electric panel to prevent parallel neutral currents. If it is a new installation, you must provide four wires (two hots, 1 neutral, & 1 ground) and connect to the four separate (appropriate) places on the dryer. If it is an existing installation and it only has three wires (two hots and a neutral) connect the neutral to both the neutral and ground connection of the dryer (the National Electrical Code allows this exception for older homes). Call a qualified electrician to do any electrical work.
When phase and neutral will short means what will be the voltage in neutral?
If the phase and neutral wires are shorted together, the voltage in the neutral wire will be the same as the phase voltage. This is because the short circuit effectively bypasses any impedance or resistance in the circuit, causing the potential difference between the phase and neutral wires to be equal.
Where are neutral and ground wires usually bonded together?
Neutral and ground wires are usually bonded together at the main service panel of a building, but should never be bonded together at any subpanel or other point downstream. This connection is made to provide a safe path for stray electrical current in case of a fault, and to ensure proper grounding and equipment safety.
How do you wire receptacles in series?
Receptacles are not wired in series. Receptacles are actually wired in parallel, what this means is that all phase wires (black) in a receptacle's box should terminate to the brass screws on each device, and all neutral (white) wires in the box should terminate on the silver screws on each device.
How do i wire your robbins and Myers hunter ceiling fan after i have put the new flywheel on i wired the two black wires together as i had taped them for identification i now have two white wires do?
If you are not sure what wires where were it is best to call an electrician. In the US, the black is power, white neutral, and green ground.
Can people die from using electronics while there charging?
No!...unless the charger is wrongly wired so that the live and neutral wires are crossed.
How do you wire a fixture that had two hot and two neutral wires?
To install a new fixture to replace the one that was removed reconnect the two hot wires together and then reconnect the two neutral wires together. Place the two wires from the new fixture to the corresponding wire colours that you just spliced together. This wiring should be down stream from the light switch. When the switch is turned on the new fixture should light. If this is not the scenario of your question then more information needs to be given.
How should I properly wire a fan and light switch together in a room?
To properly wire a fan and light switch together in a room, you should connect the hot wires from the fan and light to the hot terminal on the switch, the neutral wires to the neutral terminal, and the ground wires to the ground terminal. Make sure to follow the manufacturer's instructions and turn off the power before starting the wiring process.
How do I properly wire a light fixture with 3 sets of wires?
To properly wire a light fixture with 3 sets of wires, first identify the hot (black), neutral (white), and ground (green or bare) wires in each set. Connect the hot wires together, the neutral wires together, and the ground wires together using wire nuts. Then, connect the fixture's hot wire to the group of hot wires, the neutral wire to the group of neutral wires, and the ground wire to the group of ground wires. Finally, secure all connections with electrical tape and install the light fixture according to the manufacturer's instructions.
How can I safely install a split-wired receptacle in my home?
To safely install a split-wired receptacle in your home, you should first turn off the power to the circuit you will be working on. Then, remove the existing receptacle and separate the tab connecting the two hot terminals. Connect the hot wires to each terminal, ensuring they are securely attached. Connect the neutral wires to the neutral terminal and ground wires to the ground terminal. Finally, carefully insert the receptacle back into the electrical box, secure it in place, and turn the power back on to test the installation.
Should there be voltage between the neutral and ground?
No, ideally there should be no voltage between the neutral and ground wires in an electrical system.
Why are wires twisted together on a GFCI outlet box?
The ground wires are twisted together and then connected to the GFCI ground. The black and white wires may also be twisted together and then using a jumper wire connected to the GFCI. Hard to say without seeing exactly how it is wired.
How do you wire around the neutral safety switch?
Disconnectr the wires from the switch and connect them together
How many wires in a single phase motor?
There should be 2 or 3 wires. A hot, a neutral and sometimes a ground.
When phase and neutral will short means what will be the voltage in neutral?
If the phase and neutral wires are shorted together, the voltage in the neutral wire will be the same as the phase voltage. This is because the short circuit effectively bypasses any impedance or resistance in the circuit, causing the potential difference between the phase and neutral wires to be equal.
