answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

What does a Vacuum diagram for 1995 Chevy s10 blazer 4.3 look like?

A vacuum diagram for a 1995 Chevy S10 Blazer 4.3 will show the various vacuum hoses and components connected to the engine. It typically includes labels for each hose and component, indicating their functions and the connection points. The diagram is used for diagnosing and troubleshooting issues related to the vacuum system of the vehicle.


Where is the reverse light switch on a 2000 s10 4x4 5 speed?

On a 5-speed I'm pretty sure it is right next to where the shift tower gets bolted to the trans. It is a little ball that rides on the shifting rail. Should be pretty much the only sensor that is on the top center section of the trans.


Is it worth the time to change rod bearings in a 1988 S10 with 157K miles?

to make it worth it you should atleast repalce the main beaings and piston rings when you do it.


Will a V6 Vortec mount in place of your stock 1996 S10 2.2L manual shift 4 banger?

Yes, a V6 Vortec engine can be installed in place of the stock 2.2L engine in a 1996 S10. However, there may be additional modifications required due to differences in engine mounts, exhaust, wiring, and cooling systems between the two engines. It's recommended to consult with a mechanic or automotive specialist for a successful engine swap.


What would cause 95 S10 Blazer to overheat on the highway at 60 to 70 but not on city driving 40 to 50?

The most likely causes for the S10 Blazer to overheat at highway speeds but not in the city are a failing radiator fan clutch, a clogged radiator, or a failing water pump. At highway speeds, the engine is working harder and generating more heat, which could overwhelm a system that is not functioning properly. It's recommended to have the cooling system checked by a mechanic to diagnose and fix the issue.

Related Questions

How do you change upper ball joint on a 95 S10 pick up truck 4 cylinder?

how do you change the upper and lower ball joint on a 95 s10 pick up truck 4 cylinder rear wheel drive


Front wheels on a Chevy s10 won't fall off if the ball joint is bad?

If you let the ball joint go that bad, it can separate and you will lose control.


How do you put lower ball joints on 1994 Chevy S10 blazer. having problem getting it in straight. Am I sopose to put one end in first. How should it go in?

need to use a ball joint press.


After you install the ball joints on your 98 4x4 s10 how do you get the hub back on the ball joints?

Ball joint hub? Mabe we're not speaking the same language.


How do you change the lower left ball joint on a 92 chev s10 blazer 4x4?

Remove the tire and wheel from your 1992 Chevrolet S 10 Blazer. Removing the brake assembly and the brake rotor will give you more room to work. Remove the ball joint nut. Pound the ball joint out with a hammer. Reverse the process to install the new ball joint.


Why is 1995 s10 blazer service engine soon light on?

Have vehicle scanned to determine problem


How much should ball joint replacement cost on 2004 s10?

Need to know 2 wheel or 4 wheel drive.


What is causing a Chevy s10 to make a popping noise when turning?

bad axle joint or ball joints and turn stops can make popping


How do you replace lifters on 1995 S10 2.2?

is a 1995 s10 2.2 have solid or hydrilic lifters


Is the fender for a 1995 s10 compatible with a 1999 s10?

Yes.


How do you remove a you-joint on a 1996 Chevy s10 blazer?

or you talking about the driveshaft u-joint?


Will a transmission out of a 1995 s10 blazer fit a 2000 s10 blazer?

Yes