Maybe you have other electrical drains on that breaker line that cause it to exceed the 15 or 20 amp limit. Fix it.
More information is needed, maybe a lot more. Depending on its size you may need a new circuit for it. If you trip the breaker then don't use it and get a new circuit installed for it on its own breaker. You are probably talking about a window unit. If it is a simple 5000 BTU unit you can probably plug it into the nearest receptacle. If you trip the breaker then you need to run a new circuit for it. If it is much larger you may need to run a new circuit. If it is a 240 volt unit then you need a new circuit.
There are only two conditions that cause a breaker to trip. An overload condition of the connected load is one cause. To cause an overload condition on a breaker that supplies a garbage disposal, the motor in the unit would have to be jammed. Turn the breaker off and see if you can turn the blades in the unit. This might have to be done from the under side, look for the motors cooling fan on the bottom of the motor and see if you can turn it. If the breaker trips instantaneously when the unit is turned on, then there could be a wire grounding in the motor junction box. Same scenario, turn the breaker off, open the junction box and look for wiring problem. Use your power of smell, it is a fine diagnostic tool when it comes to burnt electrical equipment.
It is recommended to turn off the power to the central air unit before replacing the thermostat to avoid any electrical shocks or short circuits. This can be done at the circuit breaker or by switching off the power to the unit directly.
The standard SI unit for measuring mass is the kilogram (kg).
The breaker type be it a single pole or double pole will depend on what voltage the air conditioner operates on. Once the voltage is established, the sizing of the breaker depends on what the current draw of the air conditioner is.
The ampere frame rating for a circuit breaker designates how the circuit breaker should be configured. It also states the trip unit of the amp.
There is no reset button on a central air unit, there is a small breaker or fuse box outside next to the unit, it is possible the fuse is blown or breaker tripped.
Your outside central unit may be tripping the breaker due to various reasons, such as a short circuit in the wiring, a faulty compressor, or dirty condenser coils that cause the unit to overheat. Additionally, if the capacitor is failing or if there is an accumulation of debris blocking airflow, it can lead to increased electrical load and cause the breaker to trip. Regular maintenance can help prevent these issues and ensure the unit operates efficiently.
No, the breaker is there to trip at 20 amps because the supply wiring can only supply 20 amps max at that point. So a larger breaker could give you a house fire.
The wiring to the unit is either not on the right type of breaker switch or the unit is not hooked up directly to the breaker box at all.
60amp
The breaker for a central air conditioning unit is typically located in the main electrical panel of the home, which is usually found in a basement, garage, or utility room. Additionally, there is often a separate disconnect switch mounted on the exterior of the house, near the outdoor unit. This disconnect allows for safe servicing of the unit. Always ensure the power is turned off at the breaker before performing any maintenance.
That tells me the problem is with the outdoor unit. Most likely a dead compressor or fan motor. Additionally, your indoor and outdoor units are not on the same breaker.
Need more information. It doesn't seem rationale that they are protecting the same circuit unless you are substituting one for the other for a test. A unit like an air conditioner may have multiple breakers and a higher value breaker may trip because the load it is connected to is drawing current in excess of the rating of breaker.
Have you checked the breaker outside by the unit
You should not have to calculate the watts of the unit. All the information that you need will be on the nameplate of the unit. It is this information that electricians use to calculate the conductor size and breaker to supply the power to the unit.
More information is needed, maybe a lot more. Depending on its size you may need a new circuit for it. If you trip the breaker then don't use it and get a new circuit installed for it on its own breaker. You are probably talking about a window unit. If it is a simple 5000 BTU unit you can probably plug it into the nearest receptacle. If you trip the breaker then you need to run a new circuit for it. If it is much larger you may need to run a new circuit. If it is a 240 volt unit then you need a new circuit.