answersLogoWhite

0

Alternating Current (AC) refers to electricity where the Voltage on the "Hot" wire fluctuatesaround a particular level. Those levels common in the USA are 120 volts, 240 volts or 480 volts but can be other higher values for commercial power transmission i.e. 5,000 volts, 12,500 volts ect.

These voltages are actually referred to as RMS values or Root Mean Squared.

RMS refers to a mathematical formula that "averages" the fluctuations to a value. Actually .707 times the maximum value gives the listed value.

Direct Current (DC) does not flucuate the same way and in very well filtered, leveled off, electricity it can be almost a steady unvarying level. This is common in computer systems and medical equipment.

Both AC and DC Electricity flows on one wire goes through the equipment and comes back on another wire "completeing the circuit".

In your home AC comes in on one wire goes through a light switch and when the switch is turned on goes through a light bulb then out the other side of the light bulb on the "return" or "neutral" wire to your power panel and then to the ground to complete the circuit.

DC is functionally the same design for a light circuit. the difference is DC is steady at the level while in the USA AC fluctuates higher and lower around the listed voltage at a rate of 60 times a second or 60 hertz (hz). thats why you can sometimes hear bulbs "sing" or buzz. If you ever went to a concert and heard the AC power sneak through the sound system it sound like a low burrrrrrrrr sound.

You can hear the AC 60 hz sound near high power lines on the towers quite often.

Electricity is rated as volts, amps and watts for both AC and DC and in sufficient quantities both can kill and injure you.

Volts is what you see when electricity "jumps" from one thing to another.

Amps is what actually powers the equipment to do work. Think of a power tool or a vaccuum, both plug into a 120 volt outlet (the voltage) but a vaccuum that is 12 amps doesn't pick up as much dirt as a vaccuum rated at 20 or 30 amps that suck up your carpet.

Watts is a rating of the combination of volts and amps together. Confusingly referred to as "power" . This is usually used for speakers and radio amplifiers because they run off of different voltages and other factors so watts becomes easier to understand.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Natural Sciences

Did Thomas Edison want direct current or alternating current?

Thomas Edison promoted direct current (DC) as the preferred method of electrical distribution. He believed DC was safer, cheaper, and more efficient than alternating current (AC) which was being championed by his rival, Nikola Tesla.


Which apparatus changes a direct current to alternating current?

An inverter is the apparatus that changes direct current (DC) to alternating current (AC). It does this by converting the fixed voltage and direction of DC electricity into an oscillating voltage and alternating direction of AC electricity.


Would you expect to find direct or alternating current in the filament of a light bulb in your home the filament of a light bulb in a car the output of a battery charger?

Light bulb in the home - alternating current (A/C) Light bulb in a car - direct current (D/C) Output of a battery charger - direct current Input of a battery charger - usually alternating current


What is term used when an Alternating current acts like a direct current?

Perhaps you are asking how the voltage of alternating current is measured, to be equivalent to the voltage of a direct current system. Alternating current and direct current have distinct properties. With direct current, voltage is at a constant polarity, and a direct current voltage source will maintain a uniform, constant voltage level. Alternating current reverses polarity at a given frequency and therefore it's voltage continuously varies from a positive peak voltage level, through zero, to a negative peak voltage level, repeating this cycle continuously. For this reason, voltage of an alternating current system, is measured in root-mean-square (rms), which is a voltage, which when multiplied by the current in amperes, calculates power which is equivalent to that of direct current of the same voltage and current values. With a typical sinusoidal waveform, the peak voltage of alternating current is divided by the square root of 2 to determine the rms voltage. The 120 volts output in the wall outlet in our home is actually about 170 peak volts.


What are the 2 basic types of currents?

The main division is between alternating current (AC) and direct current (DC). AC is universal now for domestic and industrial supply, but DC used to be used in some places in the early part of last century. Automobiles use DC at 12V which is I think universal now. AC in domestic use can be at 50Hz (Europe and many other places) or 60Hz (North America), and can be at either 240V or 120V.