answersLogoWhite

0

For a 2 hp motor, it is recommended to use a wire gauge of either 12 or 10 AWG for typical household applications. However, it is always best to consult the motor's specification sheet or a qualified electrician to ensure the correct wire size is used based on the specific requirements of the motor and the installation.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Natural Sciences

What size wire for trolling motor?

The size of wire needed for a trolling motor depends on the motor's maximum amperage draw and the length of the wire run. A general guideline for a 12V trolling motor is 6-gauge wire for runs up to 10 feet, 4-gauge wire for runs up to 20 feet, and 2-gauge wire for runs over 20 feet to minimize voltage drop and ensure proper performance. Be sure to consult the manufacturer's recommendations for your specific trolling motor.


You want to wire up a receptacle to run a 2 hp 230 volt dust collector you have some NMD 90 14-2 available The run is about 50 feet from the panel Is this wire suitable and adequate?

No, NMD 90 14-2 wire is not suitable for a 2 hp 230 volt dust collector. You would need to use a wire with a higher ampacity such as NMD 90 10-3 wire to handle the current required for a 2 hp motor. Ensure to consult with a qualified electrician for proper wire sizing and installation.


How do you tell what gauge wire you have in your house?

The wire sheathing itself is usually marked. e.g. 14 CU 2 or 14/2 CU will indicate 14 gauge 2-wire (+ ground) copper (CU being the symbol for copper on the periodic table). For 15amp circuits you will likely has 14 gauge wire with most of that being 14/2 (Usually white, black, and bare copper).


What is difference between 10-2 and 10-3 wire?

The main difference between 10-2 and 10-3 wire is the number of conductors they have. 10-2 wire has two conductors, typically used for a hot wire and a neutral wire. 10-3 wire has three conductors, typically used for a hot wire, a neutral wire, and a ground wire.


What is 8 Gauge wire mesh thickness?

GAUGE IS THICKNESS THE SMALLER THE # THE THICKER 2- THICK 22- THIN

Related Questions

What size wire for trolling motor?

The size of wire needed for a trolling motor depends on the motor's maximum amperage draw and the length of the wire run. A general guideline for a 12V trolling motor is 6-gauge wire for runs up to 10 feet, 4-gauge wire for runs up to 20 feet, and 2-gauge wire for runs over 20 feet to minimize voltage drop and ensure proper performance. Be sure to consult the manufacturer's recommendations for your specific trolling motor.


Need to know how to wire a Campbell Hausfeld 5 hp Air Compressors to 220?

30 amp breaker 10 /2 gauge wire


Can you gauge from an 8 to a 2?

like gauge wire?


You want to wire up a receptacle to run a 2 hp 230 volt dust collector you have some NMD 90 14-2 available The run is about 50 feet from the panel Is this wire suitable and adequate?

No, NMD 90 14-2 wire is not suitable for a 2 hp 230 volt dust collector. You would need to use a wire with a higher ampacity such as NMD 90 10-3 wire to handle the current required for a 2 hp motor. Ensure to consult with a qualified electrician for proper wire sizing and installation.


How 2 make 8.0 hp go kart motor faster?

Put a 12 hp motor on it.


What is the recommended gauge for 100 amp wire made of aluminum?

The recommended gauge for 100 amp wire made of aluminum is typically 2 AWG (American Wire Gauge).


How do you tell what gauge wire you have in your house?

The wire sheathing itself is usually marked. e.g. 14 CU 2 or 14/2 CU will indicate 14 gauge 2-wire (+ ground) copper (CU being the symbol for copper on the periodic table). For 15amp circuits you will likely has 14 gauge wire with most of that being 14/2 (Usually white, black, and bare copper).


What is the recommended gauge for 12-2 low voltage wire in outdoor lighting installations?

The recommended gauge for 12-2 low voltage wire in outdoor lighting installations is typically 12 or 14 gauge wire.


What is the recommended gauge for 12/2 low voltage wire in outdoor lighting installations?

The recommended gauge for 12/2 low voltage wire in outdoor lighting installations is typically 12 or 14 gauge wire.


What is the recommended gauge size for a 100 amp aluminum wire installation?

The recommended gauge size for a 100 amp aluminum wire installation is typically 2 AWG (American Wire Gauge).


How much HP of a motor having 0.37 Kw?

About 1/2 hp


What size gauge wire for 4000w amp?

on a 4000 watt amp the best gauge wire woul be between 2 and 0