0
The size of wire needed for a trolling motor depends on the motor's maximum amperage draw and the length of the wire run. A general guideline for a 12V trolling motor is 6-gauge wire for runs up to 10 feet, 4-gauge wire for runs up to 20 feet, and 2-gauge wire for runs over 20 feet to minimize voltage drop and ensure proper performance. Be sure to consult the manufacturer's recommendations for your specific trolling motor.
What else can I help you with?
How do you wire two 12 volt marine batteries together to run a 24 volt trolling motor?
To get 24v from two 12v batteries you just link between ones positive and the others negative then connect your motor to the spare terminals, but your 12v charging system will not charge them (and any 12v equipment connected to them will burn out!) without removing the link.
What size battery do you use for trolling motor?
Usually trolling motors are 12 volts DC. You should find the amperage of the motor. Batteries are rated in amp hours. This means that the capacity of the battery will produce a certain amount of amps for a certain amount of hours. If your battery is 500 amp hours it will use any combination of amps and hours up to 500. If your motor draws 20 amps it will drain the battery in 25 hours or 10 amps it will take 50 hours to drain. By paralleling batteries you increase the draw down time. The amp hour capacities of added batteries are added together. Be sure and purchase a Deep Cycle Battery.
What size wire and breaker for a 7.5 hp motor?
For a 7.5 hp motor operating at 240V, you would typically use a 14-gauge wire and a 40 amp breaker. However, it is best to consult the motor's specifications and the National Electrical Code to determine the exact wire size and breaker needed for your specific setup.
What gauge wire for 2 hp motor?
For a 2 hp motor, it is recommended to use a wire gauge of either 12 or 10 AWG for typical household applications. However, it is always best to consult the motor's specification sheet or a qualified electrician to ensure the correct wire size is used based on the specific requirements of the motor and the installation.
When does a motor not need a neutral wire?
If the motor is operated from a three phase three wire distribution system the motor will not need a neutral wire.
Where can one purchase a MotorGuide Trolling Motor?
There are several places where you can buy a Motorguide Trolling Motor. You can visit the Motorguide website, or you can purchase a Trolling Motor direct from specialist boat companies in your location.
How do you wire two 12 volt marine batteries together to run a 24 volt trolling motor?
To get 24v from two 12v batteries you just link between ones positive and the others negative then connect your motor to the spare terminals, but your 12v charging system will not charge them (and any 12v equipment connected to them will burn out!) without removing the link.
What is the correct p rop for a motor guide four 743 trolling motor?
The correct prop for a MotorGuide 743 trolling motor is typically a 3-blade propeller, specifically designed for use with that model. The recommended size is usually around 10 inches in diameter with a pitch of 3 to 4 inches, depending on your specific boating needs and conditions. Always consult the manufacturer's guidelines or your owner's manual for the exact specifications and options available for your trolling motor.
What size of wire use for 3kw motor 380volts 3phase?
How to calculate a cable size of 3kw motor
Can you have too much thrust in a trolling motor?
Yes, you can have too much thrust in a trolling motor. Excessive thrust can lead to difficulty in precise maneuvering and control, especially in tight spaces or during slow-speed operations. It may also cause increased battery drain and potential damage to the boat's structure or components if not properly managed. It's important to choose a trolling motor with appropriate thrust for your boat size and intended use.
Can you use lawn battery for trolling motor?
yes
Do you need boat license with trolling motor?
It really depends on the state that you are in. There are different rules and regulations. In Kentucky, where I live, you have to license "anything" with a trolling motor no matter what (inflatable boat, canoe, etc.) It seems kind of silly though!
What size wire would you use to wire a motor that draws 16A from a circuit?
12
Do you need to register a boat if it has a trolling motor in vermont?
typically if the vessel is over 12 feet long, you need to register. even though there is no gas motor.
What size battery do you use for trolling motor?
Usually trolling motors are 12 volts DC. You should find the amperage of the motor. Batteries are rated in amp hours. This means that the capacity of the battery will produce a certain amount of amps for a certain amount of hours. If your battery is 500 amp hours it will use any combination of amps and hours up to 500. If your motor draws 20 amps it will drain the battery in 25 hours or 10 amps it will take 50 hours to drain. By paralleling batteries you increase the draw down time. The amp hour capacities of added batteries are added together. Be sure and purchase a Deep Cycle Battery.
What year is the Evinrude BFL2TS.97 trolling motor?
The Evinrude BFL2TS.97 trolling motor was manufactured in 1997, as indicated by the "97" in the model number. Evinrude typically uses a system where the last two digits of the model number denote the year of production. Therefore, this trolling motor is from the late 1990s.
What size of wire should i use with a 50hz motor?
Depends on the current rating which should be on the motor.
