answersLogoWhite

0

it is a valve made of glass often used in laboratory glasswares such as separatory funnels, burets, etc.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Natural Sciences

What is a burette?

A burette is a glass tube with fine gradations and a stopcock at the bottom, used in laboratory procedures for accurate fluid dispensing and titration.


How a buret is filled up?

To fill a buret, close the stopcock at the bottom, pour the solution into the top of the buret, open the stopcock slightly to allow air bubbles to escape, and then close the stopcock once the solution reaches the zero mark on the scale. Adjust the meniscus by gently tapping the buret if needed.


What is the function of straight stopcock burette?

A straight stopcock burette is used in laboratory settings to accurately measure and dispense liquids. The burette has a stopcock at the bottom that can be opened or closed to control the flow of liquid being dispensed. This design allows for precise volume measurements and controlled dispensing of liquids during experiments.


How to ensure the burette does not leak?

There are a bunch of things that can cause a stopcock to leak. There are 2 common types: Ground glass stopcocks can leak without proper application of stopcock grease either too much or not enough. It may also have dirty grease or glass. Clean it all off with acetone and reapply a very thin coating of high vacuum grease. The glass stopcock needs to be set in the housing with sufficient pressure to stop leaking. Turn it numerous times while seating the cock. There are various methods for holding the cock in place. Tefflon (plastic) & glass stopcocks should be cleaned with acetone when they are new. Do not use grease of any kind. Make sure that there is no dirt or particles between moving parts…it will scratch the plastic and crate a channel (the plastic part will have to be replaced if scratched). Assemble the stopcock properly. The rubber O-ring should be between the nut and the plastic washer. The plastic washer should be against the glass. Tighten the nut to create sufficient pressure between the glass housing and the cock to stop any leaking. It should still be able to turn easily. Rinse glassware after use and store stopcocks in the open position.


Is a buret used to heat flammable liquids?

No, a buret is a glass tube with a stopcock at the bottom that is used for delivering precise quantities of a liquid. It is not designed for heating liquids, especially flammable ones, as it may break due to thermal expansion or cause a fire. Use proper lab apparatus like a heating mantle or hot plate for heating flammable liquids.

Related Questions

What is a buret?

A buret is a glass tube with fine gradations and a stopcock at the bottom, used in laboratory procedures.


What is a burette?

A burette is a glass tube with fine gradations and a stopcock at the bottom, used in laboratory procedures for accurate fluid dispensing and titration.


How does an acid burette differ from base burette when it comes to its parts?

An acid burette typically has a stopcock that is made of glass and resistant to acidic solutions, such as made from PTFE, to prevent corrosion. It may also have a white background on the scale to help with visibility. In contrast, a base burette may have a stopcock made from materials resistant to basic solutions, like a ceramic or glass stopcock coated with PTFE. Additionally, the scale on a base burette may have a blue background to make it easier to see against basic solutions.


How do you fix a Faulty main stopcock?

Depending what is wrong with it and what type of main stopcock you have, it may need to be serviced or replaced.


What is the function of the stopcock in Bunsen burner?

The stopcock on a Bunsen burner is used to control the airflow into the burner. By adjusting the stopcock, you can regulate the amount of oxygen that reaches the flame, which allows you to control the flame size and temperature.


How do you clean a burette with stopcock stuck in it?

To clean a burette with a stuck stopcock, try soaking the burette in warm water to loosen any residue or buildup. If the stopcock is still stuck, you can try applying a lubricant such as silicone grease around the stopcock and gently tapping it to help loosen it. If these methods do not work, consider seeking help from a professional or replacing the stopcock.


What is flask and its uses?

Erlenmeyer flask is a conical flask made from glass or plastic, sometimes graduated or with a stopcock; uses: - to contain liquids or powders - to realize chemical reactions - it is the preferred flask for titration - heating of liquids (only in Pyrex glass) See also the link below.


What is erlenmeyer flask its uses?

Erlenmeyer flask is a conical flask made from glass or plastic, sometimes graduated or with a stopcock; uses: - to contain liquids or powders - to realize chemical reactions - it is the preferred flask for titration - heating of liquids (only in Pyrex glass) See also the link below.


How do you freeze the main water pipe to change the valve?

It is more normal to shut off the water supply at the suppliers stopcock (at the edge of your property near the road) when you need to do this. If you can not find the main stopcock to do this, contact your supplier. If you must resort to freezing the mains before your stopcock, you need to get a qualified plumber to do this for you.


How a buret is filled up?

To fill a buret, close the stopcock at the bottom, pour the solution into the top of the buret, open the stopcock slightly to allow air bubbles to escape, and then close the stopcock once the solution reaches the zero mark on the scale. Adjust the meniscus by gently tapping the buret if needed.


What is the function of straight stopcock burette?

A straight stopcock burette is used in laboratory settings to accurately measure and dispense liquids. The burette has a stopcock at the bottom that can be opened or closed to control the flow of liquid being dispensed. This design allows for precise volume measurements and controlled dispensing of liquids during experiments.


How to ensure the burette does not leak?

There are a bunch of things that can cause a stopcock to leak. There are 2 common types: Ground glass stopcocks can leak without proper application of stopcock grease either too much or not enough. It may also have dirty grease or glass. Clean it all off with acetone and reapply a very thin coating of high vacuum grease. The glass stopcock needs to be set in the housing with sufficient pressure to stop leaking. Turn it numerous times while seating the cock. There are various methods for holding the cock in place. Tefflon (plastic) & glass stopcocks should be cleaned with acetone when they are new. Do not use grease of any kind. Make sure that there is no dirt or particles between moving parts…it will scratch the plastic and crate a channel (the plastic part will have to be replaced if scratched). Assemble the stopcock properly. The rubber O-ring should be between the nut and the plastic washer. The plastic washer should be against the glass. Tighten the nut to create sufficient pressure between the glass housing and the cock to stop any leaking. It should still be able to turn easily. Rinse glassware after use and store stopcocks in the open position.