answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

What is meant by mcb and dp?

MCB stands for Miniature Circuit Breaker, which is a type of electrical switch that automatically disconnects a circuit in case of an overload or short circuit. DP stands for Distribution Point, which refers to a location where multiple connections from a central source are distributed to different devices or equipment.


Do circuit breakers need to be replaced?

Yes, circuit breakers can malfunction or die after a short or very long time. It could have had a minor manufacturing defect that took time to develop, such as a nick in a piece of metal. It could be that the lubricant inside spread and gummed up the works, that the spring lost tension, or any number of other things. If you reset it and it immediately trips again, you either have a short, an overloaded circuit, or the breaker is bad. Remove all loads and try again. If it still trips, odds are that it is bad. If that's the case, get a qualified electrician to swap this breaker for an identical breaker to be sure.


How many receptacales on 20 amp circuit?

Answer for USA and Canada power supply service. Presuming a "15 amp circuit" is meant as a 120 volt system with a 15 amp single pole breaker with #14 awg wire, then: Per the National Electric Code, a breaker can only be loaded to 80% of rating. Thus, a 15 amp breaker can only feed a 12 amp max load. If the loads that will be plugged into the receptacles are unknown, then 180 watts shall be used for each duplex receptacle. Maximum load allowed on the breaker is 120 x 12 = 1440 watts. Maximum receptacles allowed on circuit is 1440 / 180 = 8. Still, read the NEC or other required codes depending on the installation location and connected equipment. In Canada, there shall be not more that 12 outlets on any 2 wire branch circuit. Such outlets shall be considered to be rated at not more that 1 amp per outlet. Where the connected load is known, the number of outlets may exceed 12 providing the load current does not exceed 80 % of the rating of the over current device protecting the circuit.


Can you operate a 30 amp dryer on a 50 amp receptacle?

Yes and no. You can't put a 30A outlet on a 50A breaker as it will be a fire hazard. You can put a 50A outlet on it safely. Then you can plug the 30A load into it, but this is unwise and can be dangerous if you don't put fuses in your pigtail adapter. The best solution: Go ahead and install your 30A outlet but replace the 50A breaker with a 30A breaker. This is the safest and cleanest solution.


Can you break a jaw breaker with you mouth?

It is not advisable to try and break a jawbreaker with your mouth as it can lead to jaw pain, dental damage, or choking hazards. Jawbreakers are hard candies meant to be slowly dissolved in the mouth, not bitten into.

Related Questions

Why is it important that homes have circuit breakers?

Fuses and circuit breakers are meant to protect your home's wiring from the heat generated from fault-currents and over-currents. Over-currents happen when you exceed the amperage the fuse or breaker is rated for over a period of time (IE: drawing 20 amps on a 15 amp circuit breaker). When this occurs a fuse or circuit breaker will open the circuit so the wiring in your home will not be damaged. Over-currents happen when electricity finds a path, other than the one intended, to ground. When this happens there is very little resistance to slow the flow of electricity and the amperage through the circuit can exceed the fuse or circuit breakers rated capacity by several hundred times . These type of faults cause the fuse or circuit breaker to open the circuit very quickly.


What is meant by mcb and dp?

MCB stands for Miniature Circuit Breaker, which is a type of electrical switch that automatically disconnects a circuit in case of an overload or short circuit. DP stands for Distribution Point, which refers to a location where multiple connections from a central source are distributed to different devices or equipment.


What is open on fault?

There are isolation devices (Circuit breakers) meant to cut off or OPEN automatically when a fault occurs. The breaker has "opened" on fault.


In electrical circuits what wire protects the operator?

Earth wire is meant to protect the user in case there is earth fault in the device or circuit. Only earth wire alone is not sufficient. It needs to be provided with suitable circuit breaker that breaks the circuit automatically.


What is air cicuit breaker?

Assuming you meant a not air. A circuit breaker is a device that prevents a circuit from overloading. When the current in a circuit reaches a predefined limit, the breaker trips and opens the circuit, stopping an overload. Commonly this is done using a strip of metal with one type of metal on one side and a different one on the other. The two metals have different coefficients of thermal expansion. When the current level is reached, the strip overheats. Because one metal expands more with heat the strip bends(high coefficient of thermal expansion on the convex side). This bending opens the circuit and prevents overload.


What is meant by shunting of a circuit?

Shunting of a circuit is the electrical terminology for bypassing a circuit.


What is meant by tp and tpn circuit breakers?

The difference of TP and TPN in circuit breakers is the ability of the switch to hold a neutral position. With TPN, a neutral switch position is not possible. With TP, the breaker can be held in a neutral position.


What is the function of circuit breakers and fuses?

Protection. They shut off the power to protect the equipment circuits, the main circuits and people.


For a series rlc resonant circuit explain what is meant by series resonance and what effect it has on a circuit?

What is meant by resonance and explain the series and parallel resonance? by kathiresan


What is meant by the ground in an electric circuit?

The ground in an electric circuit is the brown copper wire.


What is difference between vacuum circuit breaker and vacuum contactor?

First thing, there is nothing like vacuum circuit contactor. It is a vacuum contactor. It has hrc fuse for protection against short circuit and have vacuum bottles in which contacts move to get close and open. It will never trip bcas it does not have tripping mechanism, it does not have operating mechanism. It's contacts are made only to make and break normal current. It is used to start and stop a motor only. It does not have ka rating for fault current. Vacuum circuit breaker is a real fault current breaker which trips during a fault like short circuit, earth fault, under or over voltage or any one. It encompasses the operating mechanism to break the contacts at a very high speed and also need a spring charging mechanism to turn the breaker on. It has very highly rated contacts inside a heavy capacity vacuum bottles. It has realese ( something like solenoid ) which pulls the plunger after it get signals from various protection relays in case of fault. It is not meant to operate for day to day start and stop operation of motor. It has ka rating for fault current. Analogus to ordinary home circuit, vcb is like a circuit breaker at home inside a panel and vc is a relay in our any of instruments at home. Analogus to low voltage situation, vcb is like a fault current ( air, or bulk oil or minimum oil ) circut breaker and vc is like an ordinary contactor


What is meant by the term buffering capacity?

buffering capacity is the ability to resist changes in acidity and alkalinity.