show solution convert 0.015 km to mm
To dilute a 100 mM solution to 5 mM, you would need to dilute it by a factor of 20. To do this, you can add 19 parts of a suitable solvent (such as water) to 1 part of the 100 mM solution. Mix thoroughly to ensure a homogeneous 5 mM solution.
To prepare a 10 mm solution, you would dilute the 4 M stock solution. Use the formula C1V1 = C2V2, where C1 is the concentration of the stock solution (4 M), V1 is the volume of stock solution needed, C2 is the desired final concentration (10 mM), and V2 is the final volume of the solution. Calculate the volume of stock solution needed to achieve the desired concentration, then add solvent (usually water) to reach the final volume.
when the vapor pressure is greater than 5 mm
To prepare a 100 mM NaCl solution, you would need to calculate the molecular weight of NaCl, which is approximately 58.44 g/mol (sodium's atomic weight is 22.99 g/mol and chlorine's is 35.45 g/mol). To make a 100 mM solution, you would need 0.1 moles of NaCl per liter of solution. This would be equivalent to 5.844 grams of NaCl per liter of solution.
To prepare 25 mM NH4HCO3, first calculate the amount of NH4HCO3 needed based on its molecular weight. Weigh out the calculated amount of NH4HCO3 and dissolve it in the appropriate volume of water to make a 25 mM solution. Finally, adjust the final volume with water if necessary.
To dilute a 100 mM solution to 5 mM, you would need to dilute it by a factor of 20. To do this, you can add 19 parts of a suitable solvent (such as water) to 1 part of the 100 mM solution. Mix thoroughly to ensure a homogeneous 5 mM solution.
Also 150 mM of sodium.
mm means millimeter there are 10 millimeters in a centimeter
FMOT @ Shee_Coldd
To prepare 100 mM phosphoric acid solution, you can dilute a more concentrated phosphoric acid stock solution to the desired concentration by adding the appropriate volume of water. Calculate the volume of the stock solution needed using the dilution formula: C1V1 = C2V2, where C1 is the concentration of stock solution, V1 is the volume of stock solution needed, C2 is the desired concentration (100 mM), and V2 is the final volume of the solution.
To prepare a 10 mm solution, you would dilute the 4 M stock solution. Use the formula C1V1 = C2V2, where C1 is the concentration of the stock solution (4 M), V1 is the volume of stock solution needed, C2 is the desired final concentration (10 mM), and V2 is the final volume of the solution. Calculate the volume of stock solution needed to achieve the desired concentration, then add solvent (usually water) to reach the final volume.
I don't know how to make the solution below. Low salt buffer: 10 mM phosphate buffer, 10 mM NaCl, pH 7.4. Could you tell me the method in detail?
The initial moles of NaCl in 1 mL of 10 mM solution is 10 µmol. The initial moles of Cl- in 4 mL of 0.05 M CaCl2 solution is 0.2 µmol. Therefore, the total moles of Cl- after mixing is 10.2 µmol. The final concentration of Cl- is 2.55 mM.
A water solution containing 50 mM tris(hydroxymethyl)aminomethane and 150 mM sodium chloride has a pH of 7,6.
I really dont know people
To prepare a 20 mM solution of Trolox, first determine the molecular weight of Trolox, which is approximately 250.3 g/mol. Calculate the amount needed by multiplying the desired molarity (20 mM or 0.02 M) by the volume of the solution you wish to prepare (in liters) and the molecular weight. For example, to make 1 liter of a 20 mM solution, dissolve 5.01 grams of Trolox in a suitable solvent, typically distilled water, and then adjust the final volume to 1 liter with the same solvent.
The area of square is : 576.0