0
What else can I help you with?
What is the fuse rating for a kettle?
A standard 3kW immersion heater will require a fuse rating of 13 A. This is because, it draws a current of 12 A.
If a 10 ampere fuse blows constantly it should be replaced with 15 ampere fuse?
Most definetly not. If a ten amp fuse has been used to protect a circuit, then it has been rated by guidlines to be the most that that circuit can hold. If you put a 15 amp fuse in its place, you are effectively allowing more current to flow through the cables than it is rated for, which will lead to excessive heating in cables and possible fire. If your fuse is constantly blowing, it means there is most likely something wrong with the cables, like a short circuit. This is extremely dangerous. Call a qualified electrician to fix the problem
What is the fuse rating for a 400 watt appliance?
The fuse rating for a 400-watt appliance can be calculated using the formula: Fuse Rating (Amps) = Power (Watts) / Voltage (Volts). For a standard voltage of 230 volts, the fuse rating would be approximately 1.74 amps, so a 2-amp fuse would typically be suitable. If the appliance operates at 120 volts, the fuse rating would be around 3.33 amps, suggesting a 4-amp fuse would be appropriate. Always check the manufacturer's specifications for the exact fuse rating.
How many 100watt 220volts bulbs can be safely used in a circuit with a fuse of 5 ampere rating?
The current (ampere) changes from a high value at switch on to a run current of of approx 0.5 amperes. The fuse blows at switch on if too many lamps are connected. It also depends on the cable used to wire up the lamps and the length of the cable.
What us the rating of the fuse which is most Commondly fitted to three pin plugs?
If you are referring to the standard plug used in the UK, then the maximum rating fuse is 13 A, which can supply a load of approximately 3 kW. But the fuse fitted must match the power-rating of the load, so lower-rated fuses are available; for example, a 3-A fuse can supply up to about 700 W.
What does 5A mean in a standard fuse?
In a standard fuse rating system, the "5A" designation indicates a 5-ampere current rating. This means that the fuse is designed to safely carry a maximum current of 5 amperes before it will blow and interrupt the circuit. It is important to select a fuse with the appropriate ampere rating to protect the circuit from overcurrent conditions.
What ampere rating of fuse is used to protect a 5.5 mm tw?
60 ampere
What is the fuse rating for a kettle?
A standard 3kW immersion heater will require a fuse rating of 13 A. This is because, it draws a current of 12 A.
How do you change your turning signal fuse on a mercury cougar?
The fuse should be inside the passenger compartment on the drivers side.Look for fuse #23. It should have a Ampere rating of 15 and the color should be blue.
What is AT and AF in MCCB?
ampere temp and ampere fuse
What is ampere rating of a fuse used to protect a 5.5 mm squared conductor?
The equivalent mm2 cross-sectional area of a 5.26 mm2 conductor is a # 10 AWG conductor. A # 10 AWG conductor size is protected by a 30 amp fuse.
Which fuse is for the tail lights for a 2001 Mercury Cougar?
In the passenger compartment fuse panel it would be fuse #23.Ampere rating 15 and the color is blue
What does the AIR rating of a fuse mean?
The AIR rating of a fuse, or Ampere Interrupting Rating, indicates the maximum fault current that the fuse can safely interrupt without causing a failure or explosion. It is a critical parameter for ensuring that the fuse can handle unexpected short circuits or overloads in an electrical system. A higher AIR rating signifies that the fuse can manage larger fault currents, providing greater protection for electrical circuits and equipment. Properly selecting a fuse with an appropriate AIR rating is essential for safety and reliability in electrical installations.
What is 1 ampere in standard units?
Ampere IS the international standard unit for electric current.
If a 10 ampere fuse blows constantly it should be replaced with 15 ampere fuse?
Most definetly not. If a ten amp fuse has been used to protect a circuit, then it has been rated by guidlines to be the most that that circuit can hold. If you put a 15 amp fuse in its place, you are effectively allowing more current to flow through the cables than it is rated for, which will lead to excessive heating in cables and possible fire. If your fuse is constantly blowing, it means there is most likely something wrong with the cables, like a short circuit. This is extremely dangerous. Call a qualified electrician to fix the problem
Is it safe to replace a 6 ampere 125 volts fuse with 6 ampere 250 volts fuse?
Yes, that is safe.
What is the ampere rating of circuit A16?
14
