answersLogoWhite

0

Saturated = 366 Deg F

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Natural Sciences

Why does water stay at the same temp after it starts to boil?

It takes a certain energy to convert water to steam. Any additional energy you supply to the water, as heat, will be taken away by water converting to steam. The maximum temperature of a liquid is its boiling point so water shows constant maximum temperature 100o Celsius (if it is pure).


What is the temperature that steam condenses to water?

Water has a boiling point of 100 degrees Celsius. When water reaches this point it becomes a gas (steam). Therefore you can say that the average temperature of steam is around 100 degrees Celsius.Answer:Steam is not the white plume from the spout of a kettle, but the hot uncondensed water vapour before this condensation takes place. It has a temperature equal to the liquid it comes from. This is not limited to 100oC except in systems that are open to the standard atmospheric pressure of 760 mm Hg.In high pressure industrial borders steam temperatures can be several hundred degrees centigrade at several atmospheres pressure. Conversely at extreme elevations water boils far below 100oC and the steam is correspondingly cooler.


How do you calculate conversion of steam to condensate?

To calculate the conversion of steam to condensate, you can use the formula: Steam Converted to Condensate = Steam Inlet - Steam Outlet This formula subtracts the amount of steam leaving the system (Steam Outlet) from the amount of steam entering the system (Steam Inlet) to determine the amount of steam that has been converted to condensate.


What is Uranus' lowest temp?

Uranus's lowest temp can get down to -355.


Does steam change colour?

Steam itself is colorless; what you see when steam appears to have a color is actually the result of light being scattered or absorbed by particles or impurities in the steam or by the background against which it is viewed.

Related Questions

Why you maintain gland steam temp in steam turbine power plant?

gland steam temp should be nearer to less than turbine lub. oil flash point.


What is the Temp of 70 psi steam?

The temperature of 70 psi steam is approximately 318°F.


Boiler 112psi what is the temp of the steam?

171 deg C


What is the cut out temp on a steam boiler?

Steam Boilers don't usually cut out on temperature but when they reach a preset pressure.


What is moist sterilization?

it is steam sterlization in which temp & pressure both works


What is a calorifier?

calorifier contains the number of coils through which steam flows. Steam from steam boiler goes to kitchen,laundry and for calorifier.Around these steam coils,water is flowing which needs to be heated. as u know temp of steam would be more than 100 deg,it heats the water which comes in contact with these coils . in most of the calorifiers,a set point mechanism is fitted which cuts the flow of steam whenrequired temp of water has attained


What is the Temp of 30 psi steam?

30 PSIG is about equal to 45 PSIA. Saturation temperature from the steam tables at 45 PSIA is about 274°F. So the steam would be 274°F, or hotter if superheated.


Why would steam rise from the hood of a 1997 neon with a cool temperature gauge?

Have you had the coolant temp sensor checked? It might be that the engine is running hot but the sensor isn't showing the temp is hot.


Why would your transmission dip stick have rust?

If thermostat is faulty and engine does not reach operating temp and stay at operating temp for a period of time it will not steam away condensation . Or too many short trips !!!


How many kg of steam required to produce 1 KWh for steam turbine of 30bar pressure and 390oC temp?

I'm currently benchmarking a number of plants in my company which produce steam for downstream processing. What is a typical kWh/kg of steam ratio I could set as a best practice target? Thanks Paul


How do you change state from a gas to a liquid?

Change in temp from gas/steam to cooler temps creates moisture into liquid molecules/condensation


Cause of increase in LP Turbine differential expansion?

1. Low vacuum at high loads 2. High HRH temp 3.High steam flow 4. high gland steam temperature