answersLogoWhite

0

The total slip on the cardan shaft is the difference in rotational speed between the driving and driven ends of the shaft, usually expressed as a percentage of the driving speed. This slip is necessary for the shaft to accommodate the misalignment between the driving and driven components it connects. It is important to keep the slip within acceptable limits to prevent excessive wear and vibration in the system.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Natural Sciences

What is a till slip?

A till slip is a printed receipt given to a customer after a purchase has been made at a store. It typically includes details such as the items bought, their prices, total cost, payment method, and any applicable discounts or promotions.


How do you read slip gauge?

To read a slip gauge, you first determine the gauge block's nominal size, which is typically marked on the block. Then, you use a micrometer or other precision measuring tool to measure the combination of slip gauges stacked together to achieve the desired measurement. The total thickness of the slip gauges used will be equal to the nominal size of the gauge block being measured.


What is a sales slip slip that is marked paid?

A sales slip marked "paid" is a document that serves as proof of a transaction where a customer has completed payment for goods or services. This slip typically includes details such as the date of purchase, items purchased, total amount paid, and payment method. The "paid" designation indicates that the seller has received the full payment, and it can be used for record-keeping or warranty purposes. This document can be important for both the buyer and seller in case of returns or disputes.


How do you use payment slip?

To use a payment slip, fill out the required information, such as your name, amount to be paid, and recipient details. Take the completed slip to the bank or payment location indicated on the slip to make the payment. The slip will be processed by the bank, and your payment will be recorded.


What is the purpose of a slip roll?

The purpose of a slip roll is for one to taste better food by making a slip roll. In addition, a slip roll has a purpose of allowing one to eat more comfortably.

Related Questions

What is another name for a driveshaft?

driving shaft, propeller shaft, Cardan shaft


What is the meaning of C in cardan shaft?

cardanic


Who invented the cardan shaft?

Gerolamo Cardano.


What happens if you use cardan shaft operating angle less than one degree?

The cardan shaft is meant to take misalignment and to operate at higher degree. But, if it is operated below 1 degree, the movement of needle rollers or the rollers in the bearing cups may not accrue resulting in brenilling. Sardeshpande. Mumbai. anandsardesh@gmail.com


Where are the grease fittings on front drive shaft of 2008 Dodge Ram?

There is only one, it is in the middle of the double cardan joint on the transfer case side. It is very hard to find with out removing the drive shaft.


What is slip yoke drive shaft?

A slip yoke is when the end of the drive shaft in a RWD vehicle plunges in and out of [most likeley] transmission when rear suspension is flexed.


What are slip ring motors?

slip ring motors are one in which the rotor is connected to the slip ring directly in which the slip ring also connected with the shaft so that it rotates with the rotor simultaneously..


What is the difference between a slip yoke and flange yoke on rear of transfer case?

A slip yoke has a splined shaft the drive shaft slides over. This allows the drive shaft to flex on rough terrain. A flange yoke has a flat plate on the transfer case and the end of the drive shaft and they bolt together.


How is the length of propeller shaft varied automatically?

via the slip joint.


Is the front drive shaft of a 1987 Chevy v10 spring loaded?

NO. It has a slip yoke.


How many degree for alignment cardan shaft?

Depending of the speed and also the technology of the cardan. Generally, you have to build with a 3° angle approximatly. The reason is to avoid to have the same needle in contact with the force. Like that, you spread the force on twice the angle installed. In industrial shaft Spicer GWB, the construction make the needles turn without rolling, thanks to a ring. I want to precise that the 3° angle is just an indicated value, not a close value (You are not obliged to build this angle with a laser alignement! If it is 3,01° or 3,2 or 3,9 OK.


Why does a propeller shaft have a slip joint?

Slip JointThe propeller shaft has to meet both of the changes i.e., the angular change coming between the gear box and differential and the change in length of the distance between the gear box and differential. The propeller shaft is also not on the same line as the gear box output shaft but it runs to the rear axle at an angle because the level of the rear axle is lower than the gear box.¾ To adjust 'angular motion', universal joints are provided.¾ To adjust for the change in length of the propeller shaft, a slip joint is provided.