0
What else can I help you with?
What is the resistance value of gold?
The resistance value of gold is very low, typically around 22 microohms at room temperature. Gold is an excellent conductor of electricity due to its low resistance, which makes it useful in electronic components where low resistance is important.
Graph of resistance of filament lamp against potential difference?
As potential difference increases in a filament lamp, resistance also increases due to an increase in temperature. The relationship between resistance and potential difference in a filament lamp is non-linear due to the temperature-dependent nature of resistance in the filament material. At low voltages, the resistance is relatively low, but as the temperature of the filament increases with higher voltages, the resistance also increases.
How do you check a resistor?
You can measure directly with an Ohm Meter, often combined with a Volt Meter. Or you can measure the voltage across the resistance and the current to calculate resistance as Current divided by Voltage.
How do you test to identify a bad resistor?
First you need to know the value of the resistor. Follow the link for a handy resistor calculator After determining the value of your resistor simply test the resistor with an ohmmeter to see if it is at true value. General use should be within + or - 5%
Why the wires in the resistance box are double folded?
The wires in the resistance box are double folded to reduce their resistance value by a factor of 4, as resistance is inversely proportional to the cross-sectional area of the wire. This allows for more precise resistance increments to be achieved by varying the length of wire exposed in the circuit.
The relationship between resistance and conductors is?
ALL resistance are conductors. just the magnitude value changes
What is inter base resistance in UJT?
The bulk resistance between the two bases, which will be different for different types of UJT. Consult the datasheet for the value.
What happens in a series circuit if one of the resistors is replaced with a resistor having a lower resistance value?
In a series circuit, if one resistor is replaced with a resistor of lower resistance, the total resistance in the circuit decreases. This leads to an increase in the overall current flowing through the circuit.
The lower the value of the coefficient of friction the what resistance to sliding?
The lower the value of the coefficient of friction, the lower the resistance to sliding. A lower coefficient of friction means less force is needed to overcome the resistance between two surfaces, making sliding easier.
The the value of the coefficient of friction the greater the resistance to sliding.?
higher
What value of tester is to be used for measuring insulation resistance of three phase 600V cables?
The typical test equipment for this is a megger. The megger is connected to two conductors at a time to test the insulation between the two.
What value of the coefficient of friction the greater the resistance to sliding?
The greater the coefficient of friction between two surfaces, the greater the resistance to sliding between them. The coefficient of friction is a measure of the amount of friction between two surfaces, with higher values indicating a stronger resistance to sliding.
What is the value for resistance 1100 ohms?
The number of ohms is, precisely, the value of the resistance.
Does measured value of resistance match the calculate value of resistance?
what is the diference betwean calculated and maesured value
When only three colour are stripes present on the body of a resistance what is the replaced value of its tolerance?
If there is no fourth band (the tolerance band) then the component's tolerance value is 20%.
How do you test pickup coil on a ATV?
A pickup coil for an ATV may be tested by measuring the resistance across the coil's electrical leads and comparing this value against the expected range specified in the ATV's shop manual.# Disconnect the pickup coil assembly from the ignition system (e.g. the CDI unit or engine control module) # Identify the coil's electrical contacts on the connector # Measure the electrical resistance between the coil's contacts with an Ohmmeter or digital volt meter.Take care not to grab both leads of your ohmmeter with your fingers while measuring this value or you'll measure your body's resistance in parallel with the coil. It's not dangerous but it might corrupt your reading.The value for working part will vary by manufacturer and model, but will typically be between 100 ohms and 350 ohms.If the coil reads as an "open circuit", or the resistance in the high 10's of k-ohms or higher, your coil is damaged and likely non-functional.
What should be the resistance value of healthy earth pit?
what is the resistance value of a healthy earth pit
