answersLogoWhite

0

For a TNIA 10 (Thermal Magnetic Circuit Breaker), the appropriate breaker size would depend on the specific requirements and rating of the circuit it is protecting. The breaker size should be chosen to match the maximum current rating of the circuit it is installed on to ensure proper protection against overcurrent. It is recommended to consult the manufacturer's specifications and guidelines for selecting the correct breaker size for the TNIA 10.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Natural Sciences

What size breaker should be used for a TNIA-10 wire?

The breaker size for a TNIA-10 wire depends on the maximum current carrying capacity of the wire, which is typically indicated on the wire's packaging or in its specifications sheet. You should select a breaker that is rated slightly higher than the wire's maximum current capacity to ensure safety and avoid overloading the wire. It is recommended to consult with a qualified electrician for specific guidance on breaker sizing for your installation.


How big of breaker do you use for 115 volt?

Depends on the wire size used in the circuit. If you use AWG # 14 wire you must use a 15 amp breaker. If it is wired with AWG # 12 wire then you use a 20 amp breaker. If a AWG # 10 wire is used then a 30 amp breaker is required. The breaker protects the wiring from overheating so you must use the proper size breaker for the wire used.


What is the minimum wire size for a 30Amp breaker?

The minimum wire size for a 30Amp breaker is typically 10 AWG for copper wire and 8 AWG for aluminum wire, according to the National Electrical Code (NEC). This wire size is necessary to safely carry the amount of current without overheating.


Can I you use existing 8 3 wire hooked to a 30amp breaker was hooked to old electric heater to wire a heater that requires 10 2 wire its a 5000watt 240volt heater?

No, you cannot use an existing 8 3 wire hooked to a 30amp breaker for a heater that requires 10 2 wire. The wire gauge and breaker size need to match the specific requirements of the new heater to ensure safety and proper function. You will need to upgrade the wiring to accommodate the 10 2 wire needed for the 5000-watt 240-volt heater.


Is a 12 gauge wire on 20 amp breaker safe for a sub panel?

No, a 12 gauge wire is rated for 20 amps, which matches the breaker size. It is not recommended to use a wire that matches the breaker size as it can result in overheating and potentially cause a fire hazard. Consider using a thicker wire, such as 10 gauge, for the 20 amp breaker to ensure safety for the sub panel.

Related Questions

What size breaker should you use for a tnia-10 wire?

25 amp breaker


What size breaker should be used for a TNIA-10 wire?

The breaker size for a TNIA-10 wire depends on the maximum current carrying capacity of the wire, which is typically indicated on the wire's packaging or in its specifications sheet. You should select a breaker that is rated slightly higher than the wire's maximum current capacity to ensure safety and avoid overloading the wire. It is recommended to consult with a qualified electrician for specific guidance on breaker sizing for your installation.


What size wire would you use on a 30amp breaker?

AWG # 10 wire.


How big of breaker do you use for 115 volt?

Depends on the wire size used in the circuit. If you use AWG # 14 wire you must use a 15 amp breaker. If it is wired with AWG # 12 wire then you use a 20 amp breaker. If a AWG # 10 wire is used then a 30 amp breaker is required. The breaker protects the wiring from overheating so you must use the proper size breaker for the wire used.


Should 25 amps breaker be replaced by 20 amps?

For typical residential house wiring 12 AWG wire is required for a 20 Amp breaker. If you change out the breaker for a 25 A breaker you would have to rewire the circuit with 10 AWG. In that case you could up the breaker to 30 Amps. All outlets and switches should be rated at the same voltage and current as the breaker.


What breaker do you use for 10 2 wire?

Use a 30 amp breaker.


What size wire is required for 120v 5amp 250ft?

Use AWG #10 wire on a 20 amp breaker.


What size wire do I need for a 30 amp breaker?

For a 30 amp breaker, you will need a wire that is at least 10 gauge in size.


What size breaker does it take to run a outdoor well?

Normally AWG #10 wire on a 30 amp breaker but it really depends on the size of the pump. The pump manufacture will specify the size wire and size breaker needed.


What is the appropriate wire size for a 25 amp breaker?

The appropriate wire size for a 25 amp breaker is typically 10 gauge wire.


What is the appropriate wire size for a 30 amp breaker?

The appropriate wire size for a 30 amp breaker is typically 10 gauge wire.


What is the recommended wire size for a 25 amp breaker?

The recommended wire size for a 25 amp breaker is typically 10 gauge wire.