answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

What size breaker needs to be installed for 15000 watt 240 volt heater?

A 15000 watt 240 volt heater would require a 62.5 amp circuit breaker. To accommodate this exact load, you would typically use the next standard breaker size above 62.5 amps, which is a 70 amp breaker to ensure safety and proper operation of the heater.


Can you use a 20 amp breaker if the amp rating on a heater is 21 amp?

No, a breaker needs to be loaded less than 80 percent. As they reach their tripping point they get hot. The circuit rating, breaker and wiring is not designed for 21 amps. The next size would be a 25 to 30 amp breaker that has #10 wire feeding it.


Why does the fuse box in my house make a clicking noise when the heater clicks on?

The clicking noise you are hearing could be the heater is overloading the breaker and it is on the verge of tripping This could be caused by the heater being to large for the circuit. Check the amperage rating on the heater and the rating on the breaker It also cold be the circuit breaker is going bad and needs to be replaced by a qualified electrician These are 2 possible answers you also could have a bad (loose) electrical connection some where in the circuit


Can you conect your dryer to a heater circuit?

Not advisable. Both units consume huge amounts of Amps (amperes = current) and the normal 20 or 30 amp breaker may not sustain prolonged operation of both. Where I live, we have two electric meters ... one just for the water heater, the other for the house and all it's electrical needs (except for the water heater).


Every time you vacuum you blow the breaker in your house can you change the breaker?

Either your breaker switch needs to be changed for a heavier one, the pool equipment needs to be put on an other circuit or better still one of its own.It is best to talk to an ellectrician about the delails involved.

Related Questions

What size breaker needs to be installed for 15000 watt 240 volt heater?

A 15000 watt 240 volt heater would require a 62.5 amp circuit breaker. To accommodate this exact load, you would typically use the next standard breaker size above 62.5 amps, which is a 70 amp breaker to ensure safety and proper operation of the heater.


What size breaker needs to be installed for 4500 watt 240 volt hotwater heater?

Answer for USA, Canada and countries running a 60 Hz supply service.You need a 30 amp 2-pole breaker and #10 AWG wire.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


Can you use a 20 amp breaker if the amp rating on a heater is 21 amp?

No, a breaker needs to be loaded less than 80 percent. As they reach their tripping point they get hot. The circuit rating, breaker and wiring is not designed for 21 amps. The next size would be a 25 to 30 amp breaker that has #10 wire feeding it.


How to replace a heater core on a 94 Lincoln mark8?

The heater box was preassembled and shipped to the Lincoln plant for assembly. The box is installed as a unit then the dashboard is installed...... Get the picture? You have to take the dashboard out and disassemble the heater box to get the job done. I advise a trip to your local library for instructions for your needs first! Not much else to say... Good luck!


Does a drip leg a city code item or should it already be on the water heater or boiler?

It needs to be installed on each part of ontario gas code


Is the blower to the heater and air conditioner fun by a fuse?

Yes, the blower for both the heater and air conditioner is typically powered through a fuse or circuit breaker within the electrical system of the HVAC unit. If the blower is not functioning, checking the fuse or breaker is a common troubleshooting step. A blown fuse or tripped breaker may indicate an electrical issue or overload that needs to be addressed. Always ensure safety by turning off power before inspecting electrical components.


How do you know the heater hose needs replacing?

You know the heater hose on a vehicle needs replacing when it beings to swell and soften. The heater hose runs from the intake manifold to the heater core.


What are the necessary specifications for a 200 amp breaker box suitable for a mobile home?

A 200 amp breaker box for a mobile home should be designed to handle the electrical needs of the home, with proper grounding and wiring connections. It should meet all relevant safety standards and be installed by a qualified electrician.


Why does the heater blow only cold air in a 1999 dodge durango?

check to see you have a thermostat installed. If you have one then you have a damper open due to no vaccum or corroded or foam seal needs replacing


Why does the fuse box in my house make a clicking noise when the heater clicks on?

The clicking noise you are hearing could be the heater is overloading the breaker and it is on the verge of tripping This could be caused by the heater being to large for the circuit. Check the amperage rating on the heater and the rating on the breaker It also cold be the circuit breaker is going bad and needs to be replaced by a qualified electrician These are 2 possible answers you also could have a bad (loose) electrical connection some where in the circuit


Can you use 14-3 wire on a 20amp breaker?

No. A 20 amp breaker needs 12 gauge wire.


How do you determine if a circuit breaker needs to be replaced?

To determine if a circuit breaker needs to be replaced, check for signs of damage such as burning smells, tripping frequently, or not resetting properly. If these issues persist after troubleshooting, it may be necessary to replace the circuit breaker.