0
What else can I help you with?
What gauge wire hold 300 amps?
To carry 300 amps of current, you would need a very large wire size, likely in the range of 3/0 or 4/0 gauge wire. It's important to consult with an electrician to ensure the wire size meets building codes and safety standards for such high amperage.
What size wire is needed for 120VDC 1275 Amps?
For that current you would need five 0000 (4/0) wires in parallel for each side of the circuit, and they would heat to 90 degrees C if used for any length of time according to the NEC tables. Those wires have a diameter of 0.46 inch exactly. There are better ways of transmitting 153 kW if there is a higher voltage available.
What wire should you use in 300 amp three phase circuit breaker?
For a 300 amp three phase circuit breaker, you should use wire that is rated for at least 300 amps. The wire gauge needed will depend on the material (copper or aluminum) and the installation method (conduit or cable), so it's recommended to consult with the National Electrical Code (NEC) or a qualified electrician for the specific wire size required. Using the correct wire size is crucial to ensure safety and prevent overheating.
What size wire is needed for 15 amps over a distance of 300 feet?
You would need at least 3 AWG at 120 volts, giving you a 4.8 percent voltage drop at the maximum load of 37.5 amps (using 30 Amps at the ordinary 80 percent rated capacity of the circuit). For 240 volts you would only need 6 AWG.
How many amps can a zero gauge wire handle?
A zero gauge wire can typically handle up to 300 amps of current. However, the exact capacity may vary depending on the specific wire material and insulation used in the wire. It is important to consult the manufacturer's specifications for the wire you are using to determine the exact ampacity.
What gauge wire hold 300 amps?
To carry 300 amps of current, you would need a very large wire size, likely in the range of 3/0 or 4/0 gauge wire. It's important to consult with an electrician to ensure the wire size meets building codes and safety standards for such high amperage.
What speaker wire for 300 watt amp?
There is no such thing as a watt amp. To determine wire size you need to know the current. Watts = Current x Voltage, so if you know the applied voltage to the load that consumes 300 watts you can get the answer. If we assume 120 volts as standard home voltage then current is 25 amps. If you had 240 volts it would be 12.5 amps. In general 14 AWG is 15 Amps 12 AWG is 20 Amps 10 AWG is 30 Amps
What size wire is needed for 120VDC 1275 Amps?
For that current you would need five 0000 (4/0) wires in parallel for each side of the circuit, and they would heat to 90 degrees C if used for any length of time according to the NEC tables. Those wires have a diameter of 0.46 inch exactly. There are better ways of transmitting 153 kW if there is a higher voltage available.
What will be the cable size for 300 A if the 3 phase voltage is 220 volts?
At least 50mm but with all the de-rating factors it might be 70mm that's if its 2 cable single phase non armoured clipped direct. Check out the tables dopey!!!! FYI 50 mm = 2 inches, 70 mm = 2.75 inches these are not wire sizes, sound more like cable outside diameters. Correct answer The wire size is dependant on the insulation factor on the wire. A few common insulations and corresponding wire sizes for 150 amps are - Size 0 R90 good for 155 amps, also with insulations of RW 75, TWH, TW75, good for 150 amps. Size 000 TW good for 165 amps.
How many amps is 250 MCM wire good for?
300 Amps if used for service entrance conductors. Table 310.15
What size awg do you need to install a 240v rec on a 50a breaker?
#8. It is better to error on the next large size. # 8 THHN 90 degree wire is rated at 45 amps. If there is a possibility that the breaker is connected to a 50 amp load the wire will be undersized. A #6 wire is rated at 65 amps. For continuous use, a load factor of 80% has to be applied. 65 x .8 = 52 amps. The only time the conductor can be smaller than the breaker size is on a motor feeder. Then the breaker is sized at 250% of the nameplate full load amps (FLA) rating of the motor. This is to allow the motor's starting current, which is about 300% FLA, to not trip the breaker on start up.
What wire should you use in 300 amp three phase circuit breaker?
For a 300 amp three phase circuit breaker, you should use wire that is rated for at least 300 amps. The wire gauge needed will depend on the material (copper or aluminum) and the installation method (conduit or cable), so it's recommended to consult with the National Electrical Code (NEC) or a qualified electrician for the specific wire size required. Using the correct wire size is crucial to ensure safety and prevent overheating.
What size wire is needed for 15 amps over a distance of 300 feet?
You would need at least 3 AWG at 120 volts, giving you a 4.8 percent voltage drop at the maximum load of 37.5 amps (using 30 Amps at the ordinary 80 percent rated capacity of the circuit). For 240 volts you would only need 6 AWG.
How many amps can a zero gauge wire handle?
A zero gauge wire can typically handle up to 300 amps of current. However, the exact capacity may vary depending on the specific wire material and insulation used in the wire. It is important to consult the manufacturer's specifications for the wire you are using to determine the exact ampacity.
What gauge wire for 240 volt at 40 amps?
The ampacity of a # 10 copper wire with an insulation factor of 90 degrees C is 30 amps. All wire voltage ratings usually drop into two categories 300 volts and 600 volts. Home wiring drops into the 300 volt range and commercial, industrial, drops into the 600 volt range.
What size service head is needed to power 250 amp 415 volt installation?
If you use 250 or 300 MCM wire you will need a 2 1/2" weather head. If you use 300 MCM wire then you will need a 3" weather head.
Could you use a 12gauge wire for a 25 amp breaker single pole?
No, a 12-gauge wire is typically rated for a 20 amp circuit. To safely handle a 25 amp breaker, you would need to use a 10-gauge wire. It's important to match the wire gauge to the amperage rating of the breaker to prevent overheating and potential fire hazards.
