answersLogoWhite

0

A 350 MCM copper conductor with an insulation factor of 75 or 90 degrees C is rated at 310 and 325 amps respectively.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Natural Sciences

How many wires are used for a 460 volt circuit breaker?

If the load is single phase and the load requires 460 volts to operate, then two conductors will be needed and they will connect to a two pole breaker. If the load is three phase and the load requires 460 volts to operate, then three conductors will be needed and they will connected to a three pole breaker. The sizing of the wires will depend upon the current that is drawn by the loads.


What is 4 pole circuit breaker?

I have never seen a four pole circuit breaker. Breakers are single, two and three pole. Single pole for 120 volts, two pole for 240 volts and three pole for three phase loads. In North America all neutrals are SN (solid neutrals) and are not switched. In certain applications using a three phase Y-connected load, where complete isolation of the load from the supply is required, the neutral line connects to one pole of a 4 pole circuit breaker.


Can you use 3 phase circuit as 3 separate single phase circuit?

Yes, a 3-phase circuit can be used as three separate single-phase circuits by connecting each load to one of the phase conductors. This allows you to operate three independent single-phase loads using the same 3-phase power source. However, caution should be taken to ensure that the loads are balanced among the phases to avoid overloading any of the phases.


What is a three phase full wave converter?

simplified circuit for three phase cycloconveretr?


How do you calculate amp draw for 115v 1 phase and the breaker size?

To calculate the amp draw of a device you need to use one of the following three formula. I = W/E, I = E/R, I =√W/R. Once the amperage of the circuit is found then the size of the breaker can be established.

Related Questions

Is there continuity between a three pole circuit breaker terminals?

No, the three individual poles of a three phase circuit breaker are not electrically connected to each other. If they were, a fault would develop internal to the breaker.


Can a circuit breaker be used to run two three phase motors?

If you mean "a" circuit breaker for two (2) three-phase motors, then yes. As long as the rating is not exceeded by the current draw of the two motors. This would, of course, require the use of a three phase breaker arrangement, and power from a three phase source. The question is kind of vague. Now, just saying that it can be done is one thing, but should it be done? That is where you need to refer to your local authority having jurisdiction (AHJ) over electrical matters. However, in a normal industrial/commercial setting (3-phase power), an MCC would normally be used, with one breaker/circuit per motor.


What is TPN MCCB?

A TPN MCCB is a three phase neutral molded case circuit breaker. This type of circuit breaker is commonly used in low voltage power distribution systems.


How many springs in 11kv vcb?

An 11kV vacuum circuit breaker (VCB) typically contains three springs, one for each phase of the circuit. These springs are part of the mechanism that operates the contacts, allowing the breaker to open and close. The exact number may vary based on the specific design and manufacturer, but three springs are standard for a three-phase system.


What does a 3 pole circuit breaker do?

It provides power to 3 conductors simultaneously, and more importantly, disconnects all three conductors simultaneously in case of a fault. A three pole breaker is used with a three phase power system.


Why neutral is not required for vacuum circuit breaker?

Air-blast circuit breakers are used to disconnect high-voltage transmission or distribution circuits in the event of a fault. One circuit breaker is required for each of the three line conductors; there is not normally a neutral conductor in high-voltage three-phase transmission/distribution lines.


How many wires are used for a 460 volt circuit breaker?

If the load is single phase and the load requires 460 volts to operate, then two conductors will be needed and they will connect to a two pole breaker. If the load is three phase and the load requires 460 volts to operate, then three conductors will be needed and they will connected to a three pole breaker. The sizing of the wires will depend upon the current that is drawn by the loads.


What is 4 pole circuit breaker?

I have never seen a four pole circuit breaker. Breakers are single, two and three pole. Single pole for 120 volts, two pole for 240 volts and three pole for three phase loads. In North America all neutrals are SN (solid neutrals) and are not switched. In certain applications using a three phase Y-connected load, where complete isolation of the load from the supply is required, the neutral line connects to one pole of a 4 pole circuit breaker.


Single phase and three phase circuit?

Yes, there is a difference between single phase and three phase circuits.


What is the rating of circuit breaker needed for a 500kva load?

To answer this question a voltage needs to be stated and whether the load is three phase or single phase. Without the voltage the amperage can not be calculated. For single phase, Amps = kva x 1000/voltage, for three phase, Amps = kva x 1000/1.73 x voltage.


What circuit you can use to run three phase motor?

It must be a three phase supply service to run a three phase motor.


If the secondary distribution center is properly connected to a primary voltage source what happens when the main circuit breaker 4ACB is pushed the the ON position?

the three phase indicator lights will illuminate