0
If gland steam temperature decreases, it can lead to reduced efficiency in steam turbine operation, as lower temperatures may not provide sufficient energy to drive the turbine effectively. This can result in decreased output power, potential issues with condensation in the system, and increased risk of equipment wear or failure. Additionally, it may require adjustments to the turbine's operational parameters to maintain performance. Overall, a decrease in gland steam temperature can negatively impact the overall efficiency and reliability of the steam system.
What else can I help you with?
When boiling water begins to turn to steam does the phase density or temperature remain the same?
When boiling water turns into steam, the temperature remains the same until all the liquid water has boiled off. The phase density decreases as the water converts to steam because steam has a lower density compared to liquid water.
Does salt affect steam temperature?
No, salt does not affect the temperature of steam. Adding salt to water increases the boiling point of the water, but once the water has turned into steam, the temperature of the steam remains the same.
What is the Temp of 60psi steam?
The temperature of steam at 60 psi (pounds per square inch) is approximately 165°C (329°F). This temperature is derived from steam tables, which relate pressure and temperature for saturated steam. At this pressure, the steam is in a saturated state, meaning it can condense back into water at this temperature.
Which has higher temperature steam or water boling in kettle?
Steam. The reason for this is water boils at the temperature of 212 degrees F. Steam can be heated to much higher temperatures than that. Some engines that are water cooled has steam at temperatures of over 700 degrees. Water basically becomes a plasma at this temperature.
What is total heat of steam?
The total heat of steam, also known as enthalpy of steam, is the amount of heat required to raise the temperature of water to its boiling point and then convert it into steam without changing its temperature. It is the sum of sensible heat and latent heat of vaporization.
What is work of gland steam cooler in steam power plant?
gland steam cooler is used to cool steam of gland sealing comes from turbine
The density of water is decrease or increase?
yes it decreases in the water
What is steam temperature after adiabatic expansion?
The steam temperature after adiabatic expansion depends on the specific conditions of the expansion process, such as initial temperature, pressure, and volume. During adiabatic expansion, the internal energy of the steam decreases, causing its temperature to drop. The final temperature can be determined using the appropriate thermodynamic equations.
What might you see and what could happen if steam seal on a steam turbine temperature is incorrect?
Of steam seal on a steam turbine temperature in incorrect could cause damage. This could cause it not to work right.
What is the Function of gland box in steam turbine?
Gland is used for the prevent leakage of oil from the gland box which is made up of copper or brass and gland box function is to support the glands which are made up of cast iron.This is called oil gland. steam gland is used for prevent the leakage of steam which exhausts air and which helps build up the vaccum in condenser is called steam gland.
What to do about turbine rotor differential expansion?
my LP turbine differential expansion increase ,when rated gland steam temperature maintain.
What is the function of the gland steam in steam turbine?
Gland steam is steam supplied to the labyrinth glands of the low pressure turbine to prevent air entering in the exhaust side, which disturbs the vacuum (± 50 mbar absolute) in the condenser. Gland steam pressure is to supply at about 0,2 bar.
What is the function of gland steam in steam turbines?
Gland steam is steam supplied to the labyrinth glands of the low pressure turbine to prevent air entering in the exhaust side, which disturbs the vacuum (± 50 mbar absolute) in the condenser. Gland steam pressure is to supply at about 0,2 bar.
Why steam enter at bottom and exit at top in gland of steam turbin rotor?
Gland steam always send from bottom because if we send the gland steam from top then it has a tendency to pass directly to the bottom (condenser) .Due to this reason gland steam is send from bottom so that it occupies total turbine inside vacuum space and seal it.
What agood repair for LP gland leak at steam turbine?
Increase the gland steam pressure if air is leaking in. If gland steam is leaking out, replace the seals. If the leak is in the casing, repair or replace the damaged parts.
Why you maintain gland steam temp in steam turbine power plant?
gland steam temp should be nearer to less than turbine lub. oil flash point.
What temperature will steam condense into a liquid?
That depends on what type of liquid created the steam. Obviously, different liquids have different evaporation, boiling, and melting points.
