answersLogoWhite

0

The result of filling a recovery cylinder with iquid refrigerant and allowing it to warm up is that the heat of the container would warm the refrigerant inside of it. The refrigerant would, as a result expand.

User Avatar

Loma Schowalter

Lvl 13
2y ago

What else can I help you with?

Continue Learning about Natural Sciences

How can you remove liquid from a r22 cylinder?

To remove liquid from an R22 cylinder, you need to first ensure the cylinder is upright and not tilted. Connect a recovery machine to the cylinder and open the liquid valve. Allow the recovery machine to pull out the liquid until only vapor remains in the cylinder.


Would you the meniscus to be more obvious in cylinder filled with oil or alcohol?

The meniscus will be more obvious in a cylinder filled with oil. This is because oil has a higher viscosity and surface tension compared to alcohol, leading to a larger curvature at the liquid-air interface of the meniscus.


Write a step-by-step process for finding the density of an unknown liquid List the laboratory equipment needed for each step?

To find the density of an unknown liquid, first, gather the necessary equipment: a graduated cylinder, a balance, and a thermometer. Begin by measuring a specific volume of the liquid using the graduated cylinder, noting the volume accurately. Next, weigh the graduated cylinder filled with the liquid on the balance to determine its mass. Finally, calculate the density by dividing the mass of the liquid by the volume measured (Density = Mass/Volume).


What is the density of liquid the mass of a graduated cylinder was 28g. 30 ml of liquid poured into a cylinder?

The difference between the weights (grams) of the empty cylinder, and with the liquid gives you the weight of the liquid. Divide that by 30 to get the density of the liquid in g/ml


When measuring with a graduated cylinder you pour liquid into a what?

When measuring with a graduated cylinder, you pour the liquid into the cylinder to a precise level. Read the measurement at the bottom of the meniscus, which is the curved surface of the liquid. Be sure to read the measurement at eye level for accuracy.

Related Questions

What would the result be if a recovery cylinder were filled with liquid refrigerant and allowed to warm up?

If a recovery cylinder were filled with liquid refrigerant and allowed to warm up, the liquid refrigerant would begin to vaporize as it absorbs heat energy from the surroundings. As the temperature of the refrigerant increases, its pressure would also rise due to the temperature-pressure relationship defined by the refrigerant's specific properties. Eventually, the refrigerant would reach a point where it transitions completely into a vapor state, filling the recovery cylinder with refrigerant vapor.


How can you remove liquid from a r22 cylinder?

To remove liquid from an R22 cylinder, you need to first ensure the cylinder is upright and not tilted. Connect a recovery machine to the cylinder and open the liquid valve. Allow the recovery machine to pull out the liquid until only vapor remains in the cylinder.


Can biogas be filled in gas cylinders for commercial use?

yes it can filled in LPG cylinder but how will you convert into liquid form


Why filled cylinder with liquid gas sink in water but ship does not?

The air (within the ship) is less dense than water.,


How do you calculate fluid height in a horizontal cylinder if I know how many gal of liquid I am going to be putting in and how many gallons the cylinder will hold if filled full?

You need more information. It all depends on the size of the cylinder


What if an empty graduated cylinder weighs 51.36g. When filled with 50.0mL of an unknown liquid. it weighs 91.35g. What is the density of the unknown liquid?

The difference in weight between the filled and empty cylinder is 91.35g - 51.36g = 39.99g. This is the weight of the 50.0mL of unknown liquid. To find the density, divide the mass (39.99g) by the volume (50.0mL) to get 0.7998 g/mL.


Would you the meniscus to be more obvious in cylinder filled with oil or alcohol?

The meniscus will be more obvious in a cylinder filled with oil. This is because oil has a higher viscosity and surface tension compared to alcohol, leading to a larger curvature at the liquid-air interface of the meniscus.


I need to calculate the volume in a cylinder in the horizontal position occupied by liquid to a certain height.?

First, take a cross-section of the cylinder and measure the area of the resulting circle that is filled with liquid (see http://www.ajdesigner.com/phphydraulicradius/hydraulic_radius_equation_pipe.php for the formula), then multiply the filled area by the length of the horizontal cylinder. To calculate the total volume of the empty horizontal cylinder, the formula is: pi * radius2 * length. For example, if the cylinder/pipe is exactly half full, the formula would be: (pi * radius2 / 2) * length. Of course, it's easier if the cylinder is upright/vertical. Then, you would just take the area of the circle and multiply by the height of the liquid from its base.


What is the liquid size for airlines?

Each person who comes on airlines is allowed to bring 1 one quart bag filled with liquid bottles of no bigger size than 3 oz.


What weighs more an empty cylender or an cylender filled with compressed gas?

Your cylinder full of gas will weigh more, for it contains the mass of the gas. Some gases, when compressed, such as CO2, are in liquid form, and quite heavy.


Why did you measure the mass of the graduated cylinder at the beginning of the experiment and not after the liquid was poured out?

The mass of the graduated cylinder was measured at the beginning of the experiment to determine the empty weight of the container before any other substances were added to it. This allowed for the accurate calculation of the mass of the liquid poured into the cylinder by subtracting the initial empty mass from the total mass measured after the liquid was added.


How do you measure the volume of liqiud?

When a liquid is filled in a cylinder, the liquids usually form a bubble called meniscus. Then you measure the lowest point of the meniscus and record the measurement.