answersLogoWhite

0

You haven't defined what you mean by "damaged" or "easily". According to

the typical popular understanding, probably the retina of the eye.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Natural Sciences

What part of the triple beam balance is the most important?

The beam of the triple beam balance is the most important part as it is used to determine the mass of an object by balancing the weights on the pans. Accuracy and precision in measurements depend on the sensitivity and calibration of the beam.


What types of rock are most damaged by freezing?

Any rocks can be "damaged" by freezing


How is laser light different from incandescent light?

The intensity of light from most light sources is inversely proportional to the square of the distance from the source. So the intensity two meters from an incandescent lamp is one quarter of the intensity at one meter, and at three meters from the lamp the intensity is one ninth of the intensity at one meter. Laser light ideally has the same intensity at any distance.


Helium neon laser ratio?

You need the gas mixture to be mostly helium, so that helium atoms can be excited. The excited helium atoms collide with neon atoms, exciting some of them to the state that radiates 632.8 nm. Without helium, the neon atoms would be excited mostly to lower excited states responsible for non-laser lines.A neon laser with no helium can be constructed but it is much more difficult without this means of energy coupling. Therefore, a HeNe laser that has lost enough of its helium (e.g., due to diffusion through the seals or glass) will most likely not lase at all since the pumping efficiency will be too low.


What is the strongest laser you can buy?

The SuperStar has the most destructive weapon ever built. Its second most powerful is its laser. The Tentloss DXR-6 Distruptor Laser v.102b (many many upgrades from its original model), powerful enough to blow up a galaxy by firring at its centre.

Related Questions

What part of the body can be most easily damaged by a laser beam?

The eyes are the most susceptible to damage from a laser beam. Direct exposure to a laser beam can cause permanent eye injury, including burns to the retina. It is important to always exercise caution and wear appropriate eye protection when working with lasers.


What part of the body will be damaged most easily by a laser beam?

The eyes are the most vulnerable part of the body to be damaged by a laser beam. The intense concentration of light can cause serious harm to the delicate tissues of the eyes, leading to vision loss or even permanent blindness. It is crucial to use appropriate eye protection when working with lasers or being exposed to laser beams.


What can you use to split a laser beam?

The most common method is through the use of a beam splitter. This employs -- to keep it simple -- a partially transparent mirror placed at a 45 degree angle relative to the laser beam. Some of the beam passes through the mirror, and the rest is reflected perpendicular to the original beam by the mirror.


What sends out a narrow intense beam of light?

Well... Most LEDs, Light Emitting Diodes, have a very narrow wavelength span, so they'd fit part of your question. However, they're not always that intense. So you're probably asking about a LASER.


Do you need electricity to work laser beam rays?

To get a LASER to work you need to excite it with energy. The most workable form of energy to do that is electricity. There ae several ways of exciting LASERs to work.


How does a vibrometer work?

Orgasms or "climaxes" are the build up and "explosion" of pleasure. When a spot of pleasure is hit repeatedly (sometimes fast and hard), a build up of pleasure begins. When your body hits the point where it can't take the pleasure anymore, it releases it's build up, hence the orgasm part.


I really need to get laser skin resurfacing done, but will it be painful?

Laser skin resurfacing involves an intense light beam which can cause burning sensations. Most doctors will give an anesthetic to ease the discomfort.


How laser light is produced a laser gun?

A laser gun produces laser light using a process called stimulated emission, where light is amplified and emitted in a focused, coherent beam. This is achieved by exciting atoms or molecules in a gain medium with energy source, such as electricity or light. This energy input stimulates the emission of photons, resulting in a concentrated beam of laser light.


What is a laster cutter?

laser cutter? laser cutter can be thought of as three main parts: a laser, a controller, and a surface. The laser is like a pencil - the beam emitted from it allows the controller to trace patterns onto the surface. The controller (usually a computer) controls the direction, intensity, speed of movement, and spread of the laser beam aimed at the surface. The surface is picked to match what the laser can act on.laser engraving machineThere are three main genres of : The most common is the X-Y table where, usually, the workpiece (surface) is stationary and the laser optics move around in X and Y directions, directing the laser beam to draw vectors. Sometimes the laser is stationary and the workpiece moves. Sometimes the workpiece moves in the Y axis and the laser in the X axis. A second genre is for cylindrical workpieces (or flat workpieces mounted around a cylinder) where the laser effectively traverses a fine helix and on/off laser pulsing produces the desired image on a raster basis. In the third method, both the laser and workpiece are stationary and galvo mirrors move the laser beam over the workpiece surface. Laser engraving machine using this technology can work in either raster or vector mode.


Are there any ways to pass through a laser sensor without being detected?

As the question asked about "passing through" a laser sensor, the answer speaks to the breaking of the laser beam. And that's not something that you can do. Breaking the beam will trigger the sensor. If an investigator has an idea about the laser itself, it may be possible to "substitute" for the beam being used in the sensor, but most laser sensors will pick up any attempts to dump another beam in over the top of the extant one. Forget about mirrors and such. The "smart" laser sensors use a beam too small to "split" with mirrors. Rerouting with fiber optics is equally futile. What you've seen on those TV shows and in movies is pie in the sky - you can't do that. About all you can do is detect the beam and avoid it.It might be worth noting that anyone using a laser may also be using infrared IR sensors. (I would.) These sensors are notlasers and are completely passive; they emit nothing at alland cannot be "seen" in any way. (See the link below "What is a PIR alarm system?" for more details). If something is worth protecting with a laser, an IR detector would be an easy "add on" to that system. In fact, given a choice, the IR would be a better first choice.


What is the most important part of a CD?

The most important part of an optical disc drive is an optical path, placed in a pickup head (PUH),[1] usually consisting of semiconductor laser, a lens for guiding the laser beam, and photo-diodes detecting the light reflection from disc's surface.


What is the most common laser beam color?

There's not really any such thing. One common and therefore cheap type of laser diode emits a red light, as does the fairly common (or at least it used to be common; the diodes are so much cheaper I imagine they mostly use them now) laboratory helium-neon laser. So if I had to pick a single color that was "common" I'd say red. There are green and even blue laser diodes now, but they're more expensive than the red ones and therefore aren't as ubiquitous.