it is likely that a floating neutral is the cause of this problem
I have never seen a 100 Volt rated outlet. Usually outlets would be rated for 110 to 120 volts for residential use, or maybe 150 volts. The rating is separate from what voltage the outlet is providing. If your outlet is supplying 100 volts, as measured by an accurate voltmeter, you have some problem in your wiring or a faulty outlet. If there is only 100 volts at the outlet get an electrician to diagnose the problem if you are not completely familiar with home wiring. In general you should never use an outlet that has a voltage or current rating less that the device will consume.
There is no need to convert a 110-volt outlet to 115 volts as they are essentially the same. The slight variation is within the normal tolerance range for electrical systems. If you need to use a device that requires 115 volts, you can safely plug it into a 110-volt outlet without the need for an adapter.
Never heard of a power tool that runs on 100 volts AC. It would have to be 108 to 120 volts or 220 to 240 volts. It will work on the 120 volt outlet if is it 60 hertz in the U.S. or 50 Hrtz in some other countries. If it is 50 Hrtz then do not use it in the U.S. without a converter.
It is not safe to plug a 120-volt device into a 130-volt outlet as the outlet may be providing too much voltage for the device to handle safely. This could lead to overheating, damage to the device, or even a fire hazard. It is recommended to use outlets that match the voltage requirement of the device being plugged in.
You would have to run new wires to obtain 240 volts or use a step-up transformer.
No conversion needed. These are nominal voltages which range from 110 to 120 volts. It will operate fine on the outlet.
I have never seen a 100 Volt rated outlet. Usually outlets would be rated for 110 to 120 volts for residential use, or maybe 150 volts. The rating is separate from what voltage the outlet is providing. If your outlet is supplying 100 volts, as measured by an accurate voltmeter, you have some problem in your wiring or a faulty outlet. If there is only 100 volts at the outlet get an electrician to diagnose the problem if you are not completely familiar with home wiring. In general you should never use an outlet that has a voltage or current rating less that the device will consume.
There is no need to convert a 110-volt outlet to 115 volts as they are essentially the same. The slight variation is within the normal tolerance range for electrical systems. If you need to use a device that requires 115 volts, you can safely plug it into a 110-volt outlet without the need for an adapter.
Never heard of a power tool that runs on 100 volts AC. It would have to be 108 to 120 volts or 220 to 240 volts. It will work on the 120 volt outlet if is it 60 hertz in the U.S. or 50 Hrtz in some other countries. If it is 50 Hrtz then do not use it in the U.S. without a converter.
Not unless you have a 110 volt supply to plug it in to. The standard General Power Outlet in Australia is 240 volts AC at 50 Hertz.
Yes.
Yes, normally, assuming it's 60 cycle (hertz) AC. In the USA, 110 volts as such is no longer used, it's really 120 plus or minus about 5 volts everywhere.
The outlet is rated for 30A, so anything up to, but not exceeding 30A can be plugged in.
no
It is not safe to plug a 120-volt device into a 130-volt outlet as the outlet may be providing too much voltage for the device to handle safely. This could lead to overheating, damage to the device, or even a fire hazard. It is recommended to use outlets that match the voltage requirement of the device being plugged in.
You would have to run new wires to obtain 240 volts or use a step-up transformer.
No, in North America the plug configuration will not allow that to happen. The blade configuration for 120 volts are in parallel where as the 220 volt configuration are in tandem.