answersLogoWhite

0

It flattens the drop to an even thickness. Otherwise surface tension would draw the drop into a ball, which will distort light passing through it.

User Avatar

Wiki User

8y ago

What else can I help you with?

Continue Learning about Natural Sciences

What do you need to make wet mount?

Put the specimen (whatever your looking at) on the slide and drop two or three drops of water on it and then put the coverslip on top, make sure there is no air bubbles.


How should you remove extra water from a wet mount slide?

To remove extra water from a wet mount slide, you can gently touch a piece of absorbent paper or tissue to the edge of the cover slip. Capillary action will draw the excess water towards the paper, helping to dry the slide. Be careful not to press too hard or you might disturb the specimen on the slide.


What are the steps of the wet mount?

the five steps to making a wet mount slide is 1.use a flat glass slide to prepare a wt mount slide 2.suck up a few drops of water from your liquid specimen into a medicaine dropper 3.pick up the wet mount slide on the 2 outer sides of the slides 4.place the specimen your using into the water 5.place the top cover slips on the top of the water with the specimen in it (: (: (: (: (: (: (: (: (: (:


What is the proper process for creating a wet mount of specimen?

a) the object is placed in a drop of water (or saline) on a clean slide. b) a coverslip is held at a 45o angle with the fingertips, and c) it is lowered carefully over the water and the object.


To view live tissue which preparation would you use?

For viewing live tissue, you can use a wet mount preparation. This involves placing a small sample of the live tissue in a drop of water on a slide, covering it with a coverslip, and viewing it under a microscope. This allows for observation of the tissue in its natural state.

Related Questions

Why is it important to put a coverslip over the drop of water when you prepare a wet mount?

You use them to cover the object on the slide, so that it doesn't slip. Usually, you put a drop of water in between the slide and cover slip as well. Also, the possibility of trapping air bubbles is reduced.


What is the final item placed on a wet mount before viewing with a light source?

Typically, a coverslip is placed on the specimen on a wet mount slide before viewing with a light source. The coverslip helps to prevent evaporation of the water, keeps the specimen in place, and provides a flat surface for better visualization under the microscope.


What is a proper way to add a saltwater solution to the cells without removing the coverslip?

You can add small amounts of water without removing the coverslip. To do this, place a single drop of water on one end of the coverslip and draw the water under the coverslip by placing a piece of paper towel on the opposite end of the coverslip. :D


How do you prepare temporary mount of a leaf peel to show stomata?

To prepare a temporary mount of a leaf peel to show stomata, you would need to carefully peel off a thin, transparent layer of the leaf. Place the peel on a glass slide and add a drop of water to ensure the peel remains hydrated. Finally, gently place a coverslip over the peel and view it under a microscope to observe the stomata.


What do you need to make wet mount?

Put the specimen (whatever your looking at) on the slide and drop two or three drops of water on it and then put the coverslip on top, make sure there is no air bubbles.


What are the steps involved in preparing a wet mount of a specimen?

To prepare a wet mount of a specimen, first, place a small drop of liquid (like water or a suitable medium) on a clean microscope slide. Next, using a pair of tweezers, carefully place the specimen in the drop. Then, gently lower a coverslip at an angle over the specimen to avoid air bubbles. Finally, observe the specimen under a microscope, adjusting the focus as needed.


How should you remove extra water from a wet mount slide?

To remove extra water from a wet mount slide, you can gently touch a piece of absorbent paper or tissue to the edge of the cover slip. Capillary action will draw the excess water towards the paper, helping to dry the slide. Be careful not to press too hard or you might disturb the specimen on the slide.


How do you make a wet mount in a microscope?

To make a wet mount in a microscope, place the specimen on a slide and add a drop of water, saline solution, or another liquid to cover it. Gently place a coverslip over the specimen at an angle to avoid trapping air bubbles. Carefully press down to flatten the specimen and remove excess liquid with a tissue.


Why do you put the cover slip at an angle when you make a wet-mount slide?

Placing the coverslip at an angle helps to minimize air bubbles from being trapped beneath the coverslip. This ensures that there is a clear and undistorted view of the specimen when observing under a microscope.


How do you prepare specimen for stereo microscope?

To prepare a specimen for a stereo microscope, first place it on a clean glass slide. If needed, add a drop of water or mounting medium to help stabilize the specimen. Then cover the specimen with a coverslip, to protect it and ensure clearer imaging under the microscope. Finally, position the slide on the stage of the stereo microscope and adjust the lighting and focus for optimal viewing.


What are the steps of the wet mount?

the five steps to making a wet mount slide is 1.use a flat glass slide to prepare a wt mount slide 2.suck up a few drops of water from your liquid specimen into a medicaine dropper 3.pick up the wet mount slide on the 2 outer sides of the slides 4.place the specimen your using into the water 5.place the top cover slips on the top of the water with the specimen in it (: (: (: (: (: (: (: (: (: (:


How do you prepare chloroform water?

To prepare chloroform water, mix chloroform with water in the desired ratio. It's important to handle chloroform with proper safety measures, such as working in a well-ventilated area, wearing gloves, and following appropriate disposal protocols for chloroform waste.