0
What else can I help you with?
Can a dimmer switch cause lights to flicker?
Yes, a dimmer switch can cause lights to flicker if not compatible with the type of bulbs being used or if the dimmer switch is malfunctioning. Flickering can also occur if the wiring connections are loose or damaged. It is recommended to use dimmer switches that are specifically designed for the type of bulbs being used to prevent flickering.
What will most likely cause arcing at a switch contact?
Arcing at a switch contact is most likely caused by loose or corroded connections, excessive current passing through the switch, or a defective switch mechanism. These conditions can create an unstable electrical path, leading to arcing between the switch contacts.
Why does the light switch not work to an existing electrical outlet?
Could be a loose connection somewhere, or a bad switch, or a bad outlet.
Could a bad circuit breaker light switch or plug outlet cause the bedroom light to flicker when turned on?
Yes a bad circuit breaker and a bad light switch can cause a light to flicker when its turned on. It could also be caused by loose wiring going or coming from that paticular circuit. it also could be something in the fixture itself causing. Checking for loose connections is your cheapest and first route to go.
I Have two storage heaters where when being used the pole switch switch becomes warm hot is this normal?
A switch becoming hot is not normal. The cause could be loose connections where the wires join the switches terminal points. This could be the cause of the heat being generated. Misalignment of the switch blades inside the switch can also cause the heat to appear. Another cause could be that the heater loads are higher that the amp rating of the switch. Switches have a label on the side of them rating what the current carrying capacity of the switch is and what the maximum amount of current that the switch can legally tolerate.
Will the windshield wiper pulse board cause the wipers to not turn off with the switch?
Yes it will. The most common problem with the board is a loose terminal.Check it real close with your fingers and find the ones that are loose and then get a soldering gun and melt it back together. That should fix it.
What can cause the turn signals not to work on a 1993 Chrysler Lebaron when the fuses and bulbs and flashers work and the turn signal switch in the steering column has been replaced?
Check the connector pins on the housing that contains the signal switch and the headlight switches that connect to the signal light switch these pens are famous for coming loose fron the circuit board thy are soldered to. had to replace my switch housing.
Have a 2003 Cadillac cts and the wipers will not shut off What could cause that?
Loose ground or pulse board failure.
What would cause the turn signals to go off and on everytime you hit a bump?
The turn signal switch is probably a bit loose, so the bumps are jostling it enough for it to switch on.
Is the breaker switch loose in your electrical system?
It is important to check if the breaker switch in your electrical system is loose.
Is the circuit breaker switch loose in your electrical system?
Is the circuit breaker switch loose in your electrical system?
Is the light switch loose in your room and in need of repair?
Is the light switch in your room loose and in need of fixing?
What would cause a 1992 Honda Accord to not turn over?
Dead battery, defective starter or ignition switch. Loose connection.
What would cause the lights not to come on until you wiggle the turn signal control arm?
Loose connections or worn parts in the light switch.
What would cause the dash broad lights to come on and off but only the dash broad lights?
Answer 1 - Instrument Lights Operate IntermittentlyWithout doing a "hands on troubleshooting" of your vehicle, no one here can be certain of the specific location and cause of your problem. However, based on your question, I suspect that the cause is a loose connection in the circuit providing power to the instrument lights, or on the instrument panel circuit board itself.It is possible also, that the instrument panel dimmer switch is wearing out.Answer 2 -The dash dimmer switch or the headlight switch is the most likely problem.
Why would a 1999 Monte Carlo have no dash board lightsi have checked all the fuses in the box on the passenger side fuse box and they are all good?
check you connection at your headlight switch,it may be loose,dirty or switch might be bad
What could cause a knocking noise from under the drivers side floor board on a Chevy Blazer?
Loose Lug nuts bad control arm...
