0
Mdajjfhkkvyvfkkgj
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What is made of two or more simple machines?
What is made up of two or more simple machines? There are only six different types of simple machines. The six simple machines are as follows: a pulley, a wheel and axle, An inclined plane, a lever, a wedge, and screw. One of them is a pulley. A pulley is a wheel with a groove along its edge, for holding a rope or cable. It helps change the direction and point of application of a pulling force. Pulleys are usually used in sets designed to reduce the amount of force needed to lift a load. The magnitude of the force is reduced, but it must act through a longer distance. Consequently, the amount of work necessary for the load to reach a particular height is the same as the amount of work needed without the pulleys. Well you know what I don't have the time to explain all of them to you so go somewheres else and look them up OK, OK goodbye. See you later. Peace out. -A
What do all simple machines have in common?
A simple machine uses a single applied force to do work against a single load force. Ignoring friction losses, the work done on the load is equal to the work done by the applied force. The machine can increase the amount of the output force, at the cost of a proportional decrease in the distance moved by the load.
What simple machines makes up the base of a light-bulb?
The bottom of a light bulb is a screw.
What are the safety measures using simple machine?
1.Never play with sharp and pointed tools.2.When carrying sharp and pointed tools like knife,position the pointed edge downward.3.Keep sharp and pointed tools in a tool box.4.Check the ladder if it is sturdy before using it.5.Check the rope if it is in good condition before using a pulley.6.Be sure that the axle is fastened safely and securely to the wheel before using it.7.Keep away from places where heavy loads are being lifted by pulleys.8.Do not leave any object on stairways.9.Be sure that any tool is in good condition before using it.10.Always keep small children away when using a sharp tool.11.When you are through using any tool, put it back in its proper place.
Advantages of full adder?
A full adder is a logical unit. The full adder must obey truth tables. They are simple, but are not speedy.
What must a wheel and axle do to be a simple machine?
they must turn together
Where is the fulcrum on a shovel?
What simple machine is the wheel based on? What do we call the “fulcrum” of a wheel?
Which is not a wheel and axle?
A tortoise is not a wheel and axle. If you want to ask a multiple choice question you must include the choices in the question.
Why is it important that the diameter of the wheel be greater than the diameter of the axle in a wheel and axle?
because the wheel turns through a much greater distance than the axle.but the smaller turn of the axle is more powerful.witten by-brenda v.=========================Answer #2:-- The fact that the wheel turns through a greater distance that the axle doesis a result, not a cause, of the wheel being bigger than the axle.-- The axle is not more powerful than the wheel. Ignoring losses, they must bothhave the same power. The axle's force is greater than the wheel's force, but to payfor it, the axle must turn through greater distance. Same as all the lever stuff.-- The diameter of the wheel needs to be greater than the diameter of the axleonly if you'd prefer not to have the axle scrape on the ground.
What simple machine does not use a force load and a turning point to do work?
There are only 6 simple machines: pulley, lever, inclined plane, wheel and axle, wedge and screw. Since a screw is an inclined plane wrapped around a central core, that would be its turning point. A wheel turns about an axle, a pulley turns about its center, and a wedge is a dual sided inclined plane. A lever must rotate about a fulcrum to be a lever, so that just leaves: Inclined plane. Its mechanical advantage is length over height, with no turning point needed.
What cannot be done by a simple machine?
Increase Work
which simple machine must be used to keep a door open?
washing machine
Why wont your left wheel on your Scott's lawn mower move when you engage the self propel after you put a new wheel on?
there is what they call a key that locks the wheel and axle together must had stuck on the old wheel
What is made of two or more simple machines?
What is made up of two or more simple machines? There are only six different types of simple machines. The six simple machines are as follows: a pulley, a wheel and axle, An inclined plane, a lever, a wedge, and screw. One of them is a pulley. A pulley is a wheel with a groove along its edge, for holding a rope or cable. It helps change the direction and point of application of a pulling force. Pulleys are usually used in sets designed to reduce the amount of force needed to lift a load. The magnitude of the force is reduced, but it must act through a longer distance. Consequently, the amount of work necessary for the load to reach a particular height is the same as the amount of work needed without the pulleys. Well you know what I don't have the time to explain all of them to you so go somewheres else and look them up OK, OK goodbye. See you later. Peace out. -A
What is the risk if the axle of the wheel is always lock?
It must be a brake problem. Have it checked now. Good brakes are a number one priority.
How do make a wheel and axle?
You Cant You Fool The Only way to do it is if you hump a cow and then spit in its face then you must light your hair onfire
How does a bike operate as a simple machine?
A bike is not a simple machine. It's a collection of several simple machines ... specifically, in order to even be a "bicycle" it must contain at the very minimum two simple machines (two wheels and axles).
